Contact   Imprint   Advertising   Guidelines

Tips and Tricks to Repair Kites - add your experience!

forum for kitesurfers


apollo4000
Rare Poster
Posts: 42
Joined: Thu Jan 03, 2013 2:27 pm
Kiting since: 2006
Local Beach: Camber Sands, The Bluff, Marazion, Lancing, Poole, Minis Bay
Favorite Beaches: Camber Sands
Style: trying hard
Gear: Kites
Blade Kiteboarding, North Kiteboarding, Cabrinha
Boards
Ocean Rodeo, Nobile, Airush, Slingshot, Crazyfly
Brand Affiliation: None

Re: Tips and Tricks to Repair Kites - add your experience!

Postby apollo4000 » Wed Apr 25, 2018 11:55 am

edt wrote:
Tue Apr 24, 2018 5:18 pm
looks good! i always cut it exactly as shown in the photo (minus the extra cut in the bladder)
Thanks mate. Wiped with alcohol, stuck the new valve on and then glued around the edge. Left for 24 hr and now waiting for an opportunity to pump the kite. It’s a little thing but I’m chuffed to bits with a little bit of diy.

apollo4000
Rare Poster
Posts: 42
Joined: Thu Jan 03, 2013 2:27 pm
Kiting since: 2006
Local Beach: Camber Sands, The Bluff, Marazion, Lancing, Poole, Minis Bay
Favorite Beaches: Camber Sands
Style: trying hard
Gear: Kites
Blade Kiteboarding, North Kiteboarding, Cabrinha
Boards
Ocean Rodeo, Nobile, Airush, Slingshot, Crazyfly
Brand Affiliation: None

Re: Tips and Tricks to Repair Kites - add your experience!

Postby apollo4000 » Thu Apr 26, 2018 5:27 pm

All good to go! Great repair kit from DrTuba.
Attachments
A23BD225-C92F-4175-A2A9-F016F142225C.jpeg
78F4C390-321F-44FE-8027-4C437F77A54B.jpeg

JaZone
Medium Poster
Posts: 116
Joined: Sat May 18, 2013 2:14 am
Kiting since: 2012
Brand Affiliation: None

Re: Tips and Tricks to Repair Kites - add your experience!

Postby JaZone » Thu Apr 26, 2018 6:28 pm

had to repair a major leading edge blowout , cause when the kite torpedoe'd , and hit the reef.
2.jpeg
3.jpeg
4.jpeg
5.jpeg
8.jpeg
10.jpeg
didn't turn out too bad, and kite flies just as the way it did before the repair.

MutantWizard
Rare Poster
Posts: 5
Joined: Sun May 13, 2018 5:52 am
Kiting since: 2011
Local Beach: Tablas
Style: Freeride, Big Air
Gear: North / CrazyFly
Brand Affiliation: None
Contact:

Re: Tips and Tricks to Repair Kites - add your experience!

Postby MutantWizard » Sun May 13, 2018 7:16 pm

Greets, my first post and thanks for the lot of tips found here.

Here is one of mine. Check the pic. This kite has seen a couple years of action when I bought it as my first and learned to ride on it. Attached it as high resolution so If you close up U will see along dacron on the trailing edge all the repairs. Fabric started falling apart from just touching it. That's when I treated the sail and its now as good if not better than when it was new. Here is how.

Pump up and open the kite. Get a small can of water based clear acrylic varnish or sometimes called acrylic emulsion. Usually this is intended for waterproofing exterior concrete walls. Mix half and half with water and apply one coat on each side of the sail. A brush or a roller is ok, just try not to be to liberal to prevent beads but still apply sufficient for it to soak into the sail fabric. It dries quickly and withing 15-20 minutes the sail is like a new plastic sheet. Try not to get any on the leading edge to prevent soak through and sticking the bladder to it. Welcome to your brand new kite!
Attachments
acrylic.jpg

JaZone
Medium Poster
Posts: 116
Joined: Sat May 18, 2013 2:14 am
Kiting since: 2012
Brand Affiliation: None

Re: Tips and Tricks to Repair Kites - add your experience!

Postby JaZone » Mon May 14, 2018 6:29 am

Did you coat the entire canopy ?

Does it add a lot of weight to the kite ?

You should do some strength tests , to see if it actually is as strong as original.

MutantWizard
Rare Poster
Posts: 5
Joined: Sun May 13, 2018 5:52 am
Kiting since: 2011
Local Beach: Tablas
Style: Freeride, Big Air
Gear: North / CrazyFly
Brand Affiliation: None
Contact:

Re: Tips and Tricks to Repair Kites - add your experience!

Postby MutantWizard » Thu May 17, 2018 4:33 am

JaZone wrote:
Mon May 14, 2018 6:29 am
Did you coat the entire canopy ?

Does it add a lot of weight to the kite ?

You should do some strength tests , to see if it actually is as strong as original.
Yes coat entire canopy if you want. Not really necessary on the dacron reinforced areas but its easy to do and makes it wind and water proof so why not.

It ads maybe about 100-200 grams which might be noticeable to a pro rider on a light wind kite but riding I cant tell the difference on any 12m or smaller kite.

You are welcome to do strength tests if you feel necessary. For me stretching it by hand was enough to know its more than good enough to ride. It becomes a reinforced plastic sheet. Windproof, waterproof and as close to original as you can get with a kite that was starting to fall apart almost by itself and was ready to be thrown into rubbish.

Keep in mind it works best after the original impregnation is gone as then the varnish soaks in completely into the canopy and no chance for peeling. That's why U should mix half / half with water. To help it soak in.


Return to “Kitesurfing”

Who is online

Users browsing this forum: Bing [Bot], Google [Bot] and 21 guests