*


All times are UTC + 1 hour



Post new topic Reply to topic
 [ 8 posts ] 
Author Message
 Post subject:
PostPosted: Sun Sep 08, 2002 7:13 pm 
Offline
Rare Poster

Joined: Mon Jun 03, 2002 1:00 am
Posts: 17
After a massive wipe out yesterday, I looked behind me to see my RRD directional floating 10 yards behind me.

Aaah I thought the leash must have broken. Nope, the circular piece of plastic with a bar in middle that secures the leash to the board was pulled clean out of the board. The end result is a hole at the tail end of the board.

I managed to retrieve the plastic leash plug that popped out and the board is over two years old so I was wondering what is the best way and what materials should I use to :

a) Secure the leash plug back into the board .

b)Patch up the board so any holes left are filled properly.

Never had to fix a board before so any advice much appreciated.


{ SHARE_ON_FACEBOOK } { SHARE_ON_TWITTER } { SHARE_ON_ORKUT } { SHARE_ON_DIGG } { SHARE_ON_MYSPACE } { SHARE_ON_DELICIOUS }
Top
Profile
 Post subject:
PostPosted: Mon Sep 09, 2002 6:12 am 
mix up some up epoxy resin with some gluing micro balloons. make sure board is dry, file groves into plug, and glue plug back into board. allow to cure about 24 hours.

John
http://www.kitesurfingnz.com


Top
 Post subject:
PostPosted: Mon Sep 09, 2002 6:58 am 
nice bit of self promo John... so when are you going to post some photo's from the weekend


Top
 Post subject:
PostPosted: Mon Sep 09, 2002 10:08 am 
Offline
Rare Poster

Joined: Mon Jun 03, 2002 1:00 am
Posts: 17
Thanks for the advice John - not sure what 'micro balloons' are though - what are they and where could I get them ?


Top
Profile
 Post subject:
PostPosted: Mon Sep 09, 2002 2:32 pm 
Offline
Very Frequent Poster

Joined: Wed Jan 09, 2002 1:00 am
Posts: 626
Hey ya big monkey...If you havn't done any resin work before the plug on a kitesurf board is a bad place to start. Get a surfboard repair guy to fix it for you. Then get some resin and fiberglass and start fixing the little dings on your boards. It takes alot of practice to repair things well and it would suck to fix your plug and have it rip out the next time something pulls on it. Nothing personal but fiberglassing stuff as you learn is the hard way to do it. Trust me I learned the hard way and now that I know how to repair things I still rather pay someone else than do it myself. PS tell me exactly what type of board from RRD you have before pouring epoxy resin into it as if it is a pollyester board the reisin will not cure and may damage the foam around the plug. ( the earlier RRD were pollyester. )
Aloha Royce.

<font size=-1>[ This Message was edited by: Royce on 2002-09-09 15:36 ]</font>


Top
Profile
 Post subject:
PostPosted: Mon Sep 09, 2002 10:13 pm 
Offline
Rare Poster

Joined: Mon Jun 03, 2002 1:00 am
Posts: 17
Thanks Royce, that sounds like good advice - here's a couple of things I left out . .

a) its a 7 ft RRD Sandwich directional made in the year 2000
b) its a board I used for learning on and very rarely use these days - so I'm not keen to spend too much fixing it
c)The plug came out very neatly and should slot back in with a bit of glue ? (Not sure about what to secure it with). If this works it will only leave a small hole in the back end of the board that just needs a bit of patching up.

what do you think ? it would be good to hear your thoughts


Top
Profile
 Post subject:
PostPosted: Tue Sep 10, 2002 1:28 am 
Offline
Very Frequent Poster

Joined: Wed Jan 09, 2002 1:00 am
Posts: 626
The bummer about the plug, even if it is a neat fit to put back in is that it will take alot of strength to keep it there. You will have to grind grooves into the plastic, set it as the guy said with microballons ( a filler for the resin that makes it more glue like ), then sand an area with coarse sand paper around the plug and lay at least 2 layers of glass over the entire plug, you will have to rough up the plug to get the glass to stick to it. Just gluiong it will only be a very short term investment. I would be surprised anyone would charge more than $50 to do the job. It will probably cost you at least half that to get the stuff. Working with that stuff is worse than fixing your own transmission on yer Ferrari. Just think how much it would suck for the same thing to happen next time you go out.
Aloha Royce.


Top
Profile
 Post subject:
PostPosted: Tue Sep 10, 2002 9:19 am 
Offline
Rare Poster

Joined: Mon Jun 03, 2002 1:00 am
Posts: 17
Thanks Royce - I think I'll take your advice and take it to someone who knows what their doing. Otherwise it sounds like I'll spend some cash and f*!k it up anyway :smile:


Top
Profile
Display posts from previous:  Sort by  
Post new topic Reply to topic
 [ 8 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: Bing [Bot], Séb and 14 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group