All times are UTC + 1 hour

Post new topic Reply to topic
 [ 23 posts ]  Go to page Previous  1, 2, 3
Author Message
 Post subject: Re: Small, portable pump for downwinders
PostPosted: Thu Oct 04, 2012 3:03 pm 
Frequent Poster
User avatar

Joined: Sun Apr 22, 2012 9:07 pm
Posts: 458
haiku wrote:
Buy a foil kite.
Best regards.


 Post subject: Re: Small, portable pump for downwinders
PostPosted: Sat Oct 06, 2012 5:48 pm 
Rare Poster

Joined: Thu Aug 02, 2007 2:31 pm
Posts: 13
Thanks for all your replies. I hadn't thought of the modified electric pump, and I looked into the foot pump but it was a bit too large for me. However, I think I found a solution that works pretty well combining the inflation bag with a high-quality balloon hand-pump (which I believe is similar to the old 2000-era Wipika style pumps). The problem I was having before was that I using a low quality exercise ball pump. After the kite reached about 3-4psi, the air would start to backflow out of the pump. So until someone pointed out a higher quality version of the hand pump, I was using a mini bike pump, which took an exteremly long time.

So my solution is as follows. First I use the Alpacka inflation bag to pump the kite up to about 0.5-1psi. Basically, this gets a large volume of air into the kite at a low pressure. Beyond this pressure, air simply rushes out the seams of the inflation bag (even if they are sealed), so I then switch to the high-quality hand-pump to get the kite up to 8-10psi. Using this system, I can leisurely inflate a 9m kite in 6-7 minutes without expending too much effort (much less effort than it would take using the hand-pump alone). Actually, the time using the hand pump is quite short. I'm not pushing in a lot of volume with the hand-pump, just enough to increase the pressure. It's not as easy as using a standard kite pump, but the entire set-up easily fits in a backpack measuring 12" by 8", and weighs less than 1 pound.

So for anyone interested, here is my recipe:
1. Qualatex ($7) or Gymnic ($15) double-action hand-pump
- Both of these pumps seem to work, but many hand-pumps do not.
- I used a Dremel to cut about 1/4" off the tip so it would fit better into the kite valve.
- I'm guessing the old Wipika kite pumps would also work, but I haven't tried.

2. Alpacka inflation-bag ($15 + shipping)
- The video on the Alpacka website is helpful.
- You have to be careful not to have any twists in the bag near the nozzle.https://www.alpackaraft.com/index.cfm/store.catalog?CategoryID=52&ProductID=74

3. Sil-Net tent seam sealer ($8) and quilting loop (this I got from a local fabric shop)
- Without sealing the seams, the bag stops pumping the kite at a much lower pressure. - If you put on the seam sealer without pre-stretching the seams, the seal will easily break when the bag inflates.

4. Sea-fit nylon hose adapters and nylon hose (see attached pictures). I found these at West Marine for under $10 total:
- 3/4" Female NPT (National Pipe Thread, which is standard) to 1/2" barbed-hose adapter (NPT stands for National Pipe Thread, which is standard. This fits into the 3/4" male NPT connector on the inflation bag).
- Roughly 9" of 1/2" diameter hose
- 1/2" barbed hose to 3/8" barbed hose adapter (3/8" fits all the kites I have owned, which includes North, SS, and now BWS - benwilsonsurf noise kites).

The entire set-up fits in a Curve Surf hydration bag that's made for surfing (basically a small backpack with an ingenious chest strap that allows you to duck-dive a wave with it on). It's a short pack that easily fits above my waist harness.

I take out the hydration pack and put the inflation bag, hand-pump, and nylon tube+adapters in a Seal-line waterproof case. I'm using the eSeries 18 for now.

So, thanks for your help. Obviously, it's a pretty involved process to put this all together. However, if you don't want to leave anything behind on the beach, at least you know this option can work. Also, I would definitely appreciate any ideas to make this better.

portable_pump.jpg [ 1.17 MIB | Viewed 962 times ]
 Post subject: Re: Small, portable pump for downwinders
PostPosted: Sat Oct 06, 2012 6:39 pm 
Medium Poster

Joined: Sun Sep 02, 2012 8:28 am
Posts: 65
seems you are quite geared-up ;)
Love when a fellow enthusiast searches, experiments, and then share his/her results!
This way, all our community learns and enriches with info.
Thanks, Sir, hat down for you! :thumb:

Display posts from previous:  Sort by  
Post new topic Reply to topic
 [ 23 posts ]  Go to page Previous  1, 2, 3

All times are UTC + 1 hour

Who is online

Users browsing this forum: Bing [Bot], Exabot [Bot], FUXIA and 24 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group