Forum for kitesurfers
-
kinchencool
- Medium Poster
- Posts: 85
- Joined: Thu Jun 14, 2012 1:15 am
- Local Beach: Bucerias, nuevo vallarta,
- Favorite Beaches: Gorge, La Ventana, Progreso, Maui, SandBar
- Style: freestyle, Kiteracing
- Gear: Slingshot RPM, Ozone Edge
- Brand Affiliation: None
-
Has thanked:
0
-
Been thanked:
0
Postby kinchencool » Sun Sep 16, 2012 11:24 pm
a friend bought an RRD Krace 70 and i guess it had a air bubble in the back so the company told him he had to brake it in 2 to get a new one and send the picture so anyways, he gave me his board to do wathever i can do with it do you guys think i can fix it, or does it worth fixing it?? would it end good?
Thanks.
-
Attachments
-
-
-
Nico
- Very Frequent Poster
- Posts: 2645
- Joined: Sun Jan 06, 2002 1:00 am
- Local Beach: private kitebeach on my doorstep,
Le Morne.
- Style: wave
- Gear: Drifter kites, wave boards
- Brand Affiliation: Cabrinha, naish
- Location: Mauritius, waterman since 1960
-
Has thanked:
0
-
Been thanked:
0
Postby Nico » Mon Sep 17, 2012 3:32 pm
Shir, anything is fixable nowadays.
They even repair broken hearts : )
Yes it is doable:
First glue the two parts together with epoxy resin and maybe one layer of cloth.
Then remove the fin box and put in a new one. then grind down the repair/ weld zone through the whole length. then put in layers of glass to refill and bond the ground out part of the previous step.
Then the esthetical part to get a clean finish (put in some GT racing strips for exemple)
bobs your uncle youve got a stronger, a bit heavier, but cheap race board.
Nico
-
gmb13
- Very Frequent Poster
- Posts: 1935
- Joined: Wed Sep 12, 2007 10:19 am
- Kiting since: 1998
- Local Beach: Flag Beach, Fuerteventura
- Style: Everything
- Gear: Indiana, Sailmon
- Brand Affiliation: Indiana, Sailmon
- Location: Fuerteventura
-
Has thanked:
36 times
-
Been thanked:
295 times
Postby gmb13 » Mon Sep 17, 2012 4:00 pm
Pretty much agree with everything Nico says,
I would however replace the back fin box.
even if you glue it together. the integrity will not be there, so you probably will have to put in new box.
You could risk just gluing the old box together, but you risk the fin splitting the whole board apart because the box will be weak
--
Gunnar
-
gbleck
- Very Frequent Poster
- Posts: 546
- Joined: Mon Oct 08, 2007 4:39 am
-
Has thanked:
0
-
Been thanked:
0
Postby gbleck » Mon Sep 17, 2012 5:21 pm
Cool. You should take some side on closeups around the fin box. Did he cut it with a jig saw? Remember to note where the box was before removing it. Not sure if it would be simpler to do before or after. Is it a sandwich construction board? If you have some scap divinycell or airex or like material then yea it should be doable at a reasonable price. May be expensive if you have to order some it might be expensive.
-
gmb13
- Very Frequent Poster
- Posts: 1935
- Joined: Wed Sep 12, 2007 10:19 am
- Kiting since: 1998
- Local Beach: Flag Beach, Fuerteventura
- Style: Everything
- Gear: Indiana, Sailmon
- Brand Affiliation: Indiana, Sailmon
- Location: Fuerteventura
-
Has thanked:
36 times
-
Been thanked:
295 times
Postby gmb13 » Mon Sep 17, 2012 8:07 pm
You will have to cut the box out. So just cut it out before glueing the board back together.
The rest is simple.
1) Buy a new box.
2) Draw a centerline
3) glue in box (quadruple check that it is straight)
4) Laminate it.
--
Gunnar
-
kinchencool
- Medium Poster
- Posts: 85
- Joined: Thu Jun 14, 2012 1:15 am
- Local Beach: Bucerias, nuevo vallarta,
- Favorite Beaches: Gorge, La Ventana, Progreso, Maui, SandBar
- Style: freestyle, Kiteracing
- Gear: Slingshot RPM, Ozone Edge
- Brand Affiliation: None
-
Has thanked:
0
-
Been thanked:
0
Postby kinchencool » Mon Sep 17, 2012 8:59 pm
Thanks guys i will defenetly get a new box for the fin and so should i just glue the board 2 pieces together or a guy told me to put like some fiberglass sticks pretty lightweight throw the EPS or would i do it just with some epoxy and also would the board still be registered or not anymore?
Also i just want it for starting to race, once i get good i can buy a mikes lab or an Aguera thats certified instead of beating a new board up when learning
-
tautologies
- Very Frequent Poster
- Posts: 10865
- Joined: Mon Feb 16, 2004 5:36 am
- Brand Affiliation: None
- Location: Oahu
-
Has thanked:
100 times
-
Been thanked:
156 times
-
Contact:
Postby tautologies » Mon Sep 17, 2012 10:35 pm
I would consider using some small rods when epoxying the parts together.
-
kinchencool
- Medium Poster
- Posts: 85
- Joined: Thu Jun 14, 2012 1:15 am
- Local Beach: Bucerias, nuevo vallarta,
- Favorite Beaches: Gorge, La Ventana, Progreso, Maui, SandBar
- Style: freestyle, Kiteracing
- Gear: Slingshot RPM, Ozone Edge
- Brand Affiliation: None
-
Has thanked:
0
-
Been thanked:
0
Postby kinchencool » Mon Sep 17, 2012 10:55 pm
Yes thats what a friend suggested me.
Thanks.
-
William Munney
- Very Frequent Poster
- Posts: 610
- Joined: Mon Sep 27, 2010 2:47 am
- Local Beach: West Meadow, GSB
- Gear: North X-Ride, Airush Sector 60, North Rebels, 6m, 7m, 9m, 12m, 16m
- Brand Affiliation: None
-
Has thanked:
0
-
Been thanked:
0
Postby William Munney » Tue Sep 18, 2012 1:35 am
gmb13 wrote:Pretty much agree with everything Nico says,
I would however replace the back fin box.
even if you glue it together. the integrity will not be there, so you probably will have to put in new box.
You could risk just gluing the old box together, but you risk the fin splitting the whole board apart because the box will be weak
--
Gunnar
Check how much the fin box and fins cost, plus the epoxy resin and supplies before you embark on this project. Make sure you use epoxy resin, not polyester. Use peelply to get a smoother finish.
Return to “Kitesurfing”
Who is online
Users browsing this forum: andrzej351, Baptiste_FR, BigBoyTonic, Bing [Bot], dp19, Google [Bot], htsc, jsanzperez, Smeagle, Tony, Windwarrior, Yahoo [Bot] and 333 guests