*


All times are UTC + 1 hour



Post new topic Reply to topic
 [ 18 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Anyone modified their Compstick bar to Lenten's setup?
PostPosted: Sat Nov 17, 2012 9:14 pm 
Offline
Frequent Poster

Joined: Fri Sep 10, 2010 6:03 pm
Posts: 409
I want to modify my 2012 Compstick bar to run the Lenten pro setup:

Attachment:
Screen shot 2012-11-17 at 20.10.02.png
Screen shot 2012-11-17 at 20.10.02.png [ 243.48 KIB | Viewed 1350 times ]


I was wondering if anyone has managed to do this theirself? It doesn't look to difficult to do, but I would need to source the chicken loop, swivel and stoppers ect.

Cheers in advance :D


{ SHARE_ON_FACEBOOK } { SHARE_ON_TWITTER } { SHARE_ON_ORKUT } { SHARE_ON_DIGG } { SHARE_ON_MYSPACE } { SHARE_ON_DELICIOUS }
Top
Profile
 Post subject: Re: Anyone modified their Compstick bar to Lenten's setup?
PostPosted: Sat Nov 17, 2012 10:10 pm 
Offline
Very Frequent Poster

Joined: Fri Oct 30, 2009 9:13 pm
Posts: 935
I assume you are looking for an above the bar trim? If so here is a mod I do to my Slingy bars. The bar on the right has been modded. Takes about 30 min. All you have to do is get a clam cleat and trim rope ( a pull pull strap would work as well ). Double back your new center line and tie a figure 8 knot to keep the center line in place. I had all so cut this bar to 14" to use with my 7/9m fuels. Hope that is what your looking for.

One more thing. I showed one of our locals this and he ordered the cleat from Switch kites. He seems to like it a lot.

Image


Top
Profile
 Post subject: Re: Anyone modified their Compstick bar to Lenten's setup?
PostPosted: Sat Nov 17, 2012 11:23 pm 
Offline
Frequent Poster

Joined: Fri Sep 10, 2010 6:03 pm
Posts: 409
I want above the bar trim, but I also want to do away with all the crap running through the centre hole. I just want one single PU line running through the centre hole. This will obviously do away with the safety mechanism, but to be honest I haven't pulled my safety for years. I think using the O-shit handles as a safety will be perfectly fine...? That Lenten pro setup looks so clean! The Ozone bar setup is also really clean, I really don't see the need for 3 lines running through the bar? Below the bar depower is also retarded!

Your setup looks really nice BTW! It must be cheaper for you to replace the red centre line compared to buying a slingy one?


Top
Profile
 Post subject: Re: Anyone modified their Compstick bar to Lenten's setup?
PostPosted: Sat Nov 17, 2012 11:39 pm 
Offline
Frequent Poster

Joined: Fri Sep 10, 2010 6:03 pm
Posts: 409
What diametre spectre did you use mate? Did you find getting the height right for your depower cleat OK? Also, how did you go about chopping down your Slingy bar? I saw a video of someone cutting down an Ozone bar once but can't find it anywhere now :(


Top
Profile
 Post subject: Re: Anyone modified their Compstick bar to Lenten's setup?
PostPosted: Sun Nov 18, 2012 12:01 am 
Offline
Frequent Poster

Joined: Mon Sep 26, 2011 4:49 am
Posts: 374
try Wainman Hawaii


Top
Profile
 Post subject: Re: Anyone modified their Compstick bar to Lenten's setup?
PostPosted: Sun Nov 18, 2012 4:03 am 
Offline
Very Frequent Poster
User avatar

Joined: Sun Jan 02, 2011 11:45 pm
Posts: 1386
Location: The Gorge
knotwindy wrote:
try Wainman Hawaii


yeah, honestly modding things can be neat but it sounds like it might be a better idea to sell the bar stock and buy one that you like better...


Top
Profile
 Post subject: Re: Anyone modified their Compstick bar to Lenten's setup?
PostPosted: Sun Nov 18, 2012 5:00 am 
Offline
Very Frequent Poster
User avatar

Joined: Fri Jul 16, 2010 6:27 am
Posts: 2245
Location: Ford Lake, Michigan
this mod is no more difficult than swapping out a used chicken loop line. just make sure you get the right diameter line otherwise the stopper wont work right.


Top
Profile
 Post subject: Re: Anyone modified their Compstick bar to Lenten's setup?
PostPosted: Sun Nov 18, 2012 5:44 am 
Offline
Frequent Poster

Joined: Mon Sep 26, 2011 4:49 am
Posts: 374
i did not necessarily mean get a WH bar
i meant if you want to part out a set up, you should check out the WH stuff
the chicken loop, covered lines and cleat are the same and you can either swap out the swivel or just use the one you have


Top
Profile
 Post subject: Re: Anyone modified their Compstick bar to Lenten's setup?
PostPosted: Sun Nov 18, 2012 11:03 am 
Offline
Frequent Poster

Joined: Fri Sep 10, 2010 6:03 pm
Posts: 409
I'll look into the Wainman setup and see if I can mod that to my bar. The Ozone setup is also pretty mint, but I just don't like the bar as it's too thick and not grippy enough...it gets torn out of your hands easily on unhooked kiteloops. It would be a mission to mod that setup to the Slingy bar as you would need almost every single Ozone component!
I do really like the look of TheJoe's setup though, it woud be cheaper to change depower ropes as you could just by a reel of the stuff!

@TheJoe could you please explain exactly how you attached the Clamcleat with the ring on the back? Did you need to cut any existing lines? Also, how did you go about cutting down your bar? It looks like a sweet setup for my 7m Fuel.

I think this is the cheapest and easiest solution, which will maintain the original safety system :thumb:


Top
Profile
 Post subject: Re: Anyone modified their Compstick bar to Lenten's setup?
PostPosted: Sun Nov 18, 2012 12:58 pm 
Offline
Very Frequent Poster

Joined: Fri Oct 30, 2009 9:13 pm
Posts: 935
knotwindy wrote:
i did not necessarily mean get a WH bar
i meant if you want to part out a set up, you should check out the WH stuff
the chicken loop, covered lines and cleat are the same and you can either swap out the swivel or just use the one you have


I tried this and they just don't make them as spares. At least when I wanted to just get the center line and chicken loop.

For the clam cleat I just used 2 stainless steel nut and bolts I got from the local hardware store. The piece of plastic is there just to act as a washer as the bolts are small and go thru the rope. I just didn't want them to have a chance to pull thru. I don't even remember where I got the plastic.

Cutting the bar is easy. First you have to cut the rubber sheath around the bar ends off so you can drill out the rivets. Next you want to measure how far from the end the foam is cut back and write it down. Figure out how much you want to cut your bar. I just went to 14" so I cut 1 & 1/2" off both ends with a hack saw. then cut back the foam. I put the ends back on lined them up and marked where to drill the holes for the rivets. I pulled off the ends to drill the holes then before I put them back on I used a 2 part epoxy for a little extra strength hold. Put the rivets in and done.

To get the center line the right length I just measured the original setup from the top of the chickenloop to the swivel and did my best to match that length. I want to say it is somewhere around 27". I then made my center line and trim strap that length and put everything back together. Then I went outside and made sure it was right by doing a basic line tune on the bar. Same as you would if your front lines are too long.

As for the the rope diameter I want to say it is 1/8 spectra I got from West Marine. It is the same size as the slingshot center line smaller half.

Next time I mod a bar I plan on making an in depth tutorial. I have actually use the 14" bar on a 13m fuel and it even worked there. I all so have cut down a Wainman bar to 12.5" (I screwed up on my take off's) But the bar works great on the 7m gypsy. Hope this helps.


Top
Profile
Display posts from previous:  Sort by  
Post new topic Reply to topic
 [ 18 posts ]  Go to page 1, 2  Next

All times are UTC + 1 hour


Who is online

Users browsing this forum: Bing [Bot], davesails7, Dirk, Google [Bot], Google Feedfetcher, Jackie Treehorn, jb+wind=40feet, looktodskies, wrogu and 27 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group