Forum for kitesurfers
-
Pascale
- Medium Poster
- Posts: 74
- Joined: Mon Aug 06, 2007 12:30 pm
- Brand Affiliation: None
- Location: Quebec City, Canada
-
Has thanked:
0
-
Been thanked:
0
Postby Pascale » Tue Jan 15, 2013 11:31 pm
Hi,
I had a slow leak on my kite so I did the soapy water trick and found a hole. Fixed it.
Leading edge back in.
Pump it again.
Slow leak again but this time very slow: instead of 1 hour, I'd say that it stays decently firm for 3 hours or so.
Struts were clipped so the problem doesn't seem there.
I read here that it could be a valve problem.
1) maybe i don't tighten the inflate valve enough
2) maybe the rubber seal is worn.
So here are my questions:
1) Since it says on the LE not to tighten the valve too much when the kite is not inflated, is there a risk of ruining something by tightening too much the valve when it is inflated?
2) since at this time of year kite supplies are replaced by ski supllies in the local shop, what could I use to replace my (maybe) worn rubber seal? (I mean homemade)
Thanks
-
hobie1463
- Rare Poster
- Posts: 47
- Joined: Wed Mar 28, 2007 7:54 am
-
Has thanked:
0
-
Been thanked:
0
Postby hobie1463 » Wed Jan 16, 2013 12:02 am
Mate, try replacing the 2 way valve. The get sand in them and leak.
Just a sugestion.
-
Dr Makani
- Medium Poster
- Posts: 101
- Joined: Sat Nov 17, 2012 7:39 pm
- Local Beach: CA, HI
- Brand Affiliation: None
- Location: CA, HI
-
Has thanked:
0
-
Been thanked:
0
Postby Dr Makani » Wed Jan 16, 2013 12:35 am
Had a similar issue a while ago. Drove me crazy. Dragged the whole kite into my pool and found following:
Check inflate/deflate valve plugs. After spraying them with dish soap I could see fine bubbling AFTER 5 min between valve throat and plug. Gave the plug one (1) wrap with Teflon tape, glued the tape and viola ...
Also one of my air tubes connecting LE and strut was slowly, very slowly leaking. These tubes are fastened with zip ties to outlets on either end. Obviously some of these zip ties get loose over time and allow a small air leak.
It's almost a Zen therapy to find these super slow air leaks.
peace
-
southflorida
- Medium Poster
- Posts: 167
- Joined: Sat Apr 09, 2011 1:15 pm
- Style: flat water, go fast, practice tricks
- Brand Affiliation: None
-
Has thanked:
0
-
Been thanked:
0
Postby southflorida » Wed Jan 16, 2013 12:41 am
Had same problem, also with a Cab kite, but my problem was not brand related. Some sand had gotten between the bladder and leading edge. On a microscopic scale, the particular type of sand was sharp, and would make new super-small very difficult to find hole(s) each time I re-assembled and inflated the bladder. I repaired it like four times until I decided to violently shake any sand out (with bladder removed) and repair the last hole. It's been good since.
The clue to me was that these pin-holes would keep showing up on the same side of the bladder relative to the inflation point.
This may or may not be your problem, but sand or any other debris between the bladder and leading edge is bad news no matter what.
-
Vogelm1
- Rare Poster
- Posts: 24
- Joined: Mon Feb 13, 2012 11:44 pm
- Local Beach: Great Lakes
- Favorite Beaches: OBX, Cayman, TCI
- Style: Freeride
- Gear: 2021 North Orbit - 14m, 11m, 8m; 137 Carved Imperator 7
Armstrong Foil w/Core SLC 135 cm board; Core 12m XLite
- Brand Affiliation: None
- Location: Great Lakes
-
Has thanked:
5 times
-
Been thanked:
2 times
Postby Vogelm1 » Wed Jan 16, 2013 1:43 am
Check to be sure the sealing washer (rubber washer on bottom of valve that goes over the male threaded end) didn't blow off. It's easy to miss because it blends in well with the valve. This has happened to me twice now when deflating Cabs - the initial blast of air causes it to fly. I never realized it was gone until next session when kite was getting soft after an hour or so. Now I hold my hand over the valve while unscrewing to catch it if it does happen again.
-
Pascale
- Medium Poster
- Posts: 74
- Joined: Mon Aug 06, 2007 12:30 pm
- Brand Affiliation: None
- Location: Quebec City, Canada
-
Has thanked:
0
-
Been thanked:
0
Postby Pascale » Wed Jan 16, 2013 2:00 pm
hobie1463 wrote:Mate, try replacing the[img] 2 way valve. The get sand in them and leak.
Just a sugestion.
Hi,
Are you talking about this:
http://www.fcwatersports.co.uk/media/ca ... lock_1.jpg
(sorry I don't know how to add a picture to my post)
Thanks
-
ronnie
- Very Frequent Poster
- Posts: 4192
- Joined: Sun Jul 24, 2005 6:39 pm
-
Has thanked:
31 times
-
Been thanked:
61 times
Postby ronnie » Wed Jan 16, 2013 4:05 pm
The Airlock valve was upgraded in recent years (but I cant remember what year) where they modified the non-return flap so that there was less resistance when pumping up the kite, so if you have one of the older valves, its worth upgrading for the easier pumping.
They have now upgraded the Airlock valve again for 2013 so it has a cap and doesn't need an adaptor.
http://www.4kiteboarding.com/2013-cabri ... -kite.html
It may cost about $7? US.
I have a similar problem on my 10m Xbow which I will try to find the source of in case it isn't the LE bladder.
-
Kiteus Maximus
- Medium Poster
- Posts: 146
- Joined: Wed Dec 05, 2012 10:37 pm
-
Has thanked:
0
-
Been thanked:
0
Postby Kiteus Maximus » Wed Jan 16, 2013 8:51 pm
If you want to try the inexpensive solution first then go buy some plumber's tape (aka teflon tape) at your local hardware store and wrap it around your valve plug. It creates an air tight seal. If that stops the leak then you know it is your valve. Plumber's tape cost about 30 cents a roll.
-
PVITfrumBYRAM
- Frequent Poster
- Posts: 211
- Joined: Sat May 22, 2010 3:20 am
- Local Beach: Hatteras Island, NC
- Style: Instruction
- Brand Affiliation: None
-
Has thanked:
0
-
Been thanked:
0
Postby PVITfrumBYRAM » Fri Jan 18, 2013 9:16 pm
I haven't seen this on many Cabrinhas but you never know when you get a bad bladder. I worked on a Crazy fly for 3 days taking the bladder out patching holes and so on. I found that the bladder was old, and I could see where the rubber was starting to crack. They weren't holes leaking air even when pumped up and squeezing the section of bladder to try to force air through. However, if I stretched the area a bit, pulling the rubber perpendicular to the line of the crack, and squeezed the tube I would begin to see bubbles from the soapy water. Sometimes it helps to have some bright lights and holding clipboard behind the bladder. I went over this bladder carefully with out air in it, getting different view points to examine for more cracks. It took a while but I sharpie each suspected area and then got the spray bottle to verify if the crack was all the way through the bladder. Something else to look for is along the seam of the bladder. It's easy for pinholes and cracking to form and hide from scrutiny. If your bladder is still in the kite, pump it up and dunk it in the water, if you see bubbles, narrow down between which struts, or using soapy water, spray it and ifind the leak, dry it with a towel and use a fresh sharpie to try to get the ink to go through the nylon to the bladder so its easier to get close to the leak.
-
PVITfrumBYRAM
- Frequent Poster
- Posts: 211
- Joined: Sat May 22, 2010 3:20 am
- Local Beach: Hatteras Island, NC
- Style: Instruction
- Brand Affiliation: None
-
Has thanked:
0
-
Been thanked:
0
Postby PVITfrumBYRAM » Fri Jan 18, 2013 9:18 pm
I haven't seen this on many Cabrinhas but you never know when you get a bad bladder. I worked on a Crazy fly for 3 days taking the bladder out patching holes and so on. I found that the bladder was old, and I could see where the rubber was starting to crack. They weren't holes leaking air even when pumped up and squeezing the section of bladder to try to force air through. However, if I stretched the area a bit, pulling the rubber perpendicular to the line of the crack, and squeezed the tube I would begin to see bubbles from the soapy water. Sometimes it helps to have some bright lights and holding clipboard behind the bladder. I went over this bladder carefully with out air in it, getting different view points to examine for more cracks. It took a while but I sharpie each suspected area and then got the spray bottle to verify if the crack was all the way through the bladder. Something else to look for is along the seam of the bladder. It's easy for pinholes and cracking to form and hide from scrutiny. If your bladder is still in the kite, pump it up and dunk it in the water, if you see bubbles, narrow down between which struts, or using soapy water, spray it and ifind the leak, dry it with a towel and use a fresh sharpie to try to get the ink to go through the nylon to the bladder so its easier to get close to the leak.
Return to “Kitesurfing”
Who is online
Users browsing this forum: AKBL, andrzej351, Bing [Bot], bittersvolcom, bragnouff, Brent NKB, Exage, foilkite90, Google [Bot], grigorib, Hasse, mede, plasma180, universalflush, UrosR, wowkitesurf, Yahoo [Bot] and 569 guests