Paper Chaser - First Board - Thanks to the list!!!

ddeville · **Joined:** Mon Jan 26, 2009 12:28 am **Posts:** 2

Hello gang. This is the first board that I've made. I have experience with composites in building large model rockets, but it was thanks to the information I learned on this list that I was able to make such a great first attempt. I'm really excited about making more.

Attachment:

Jan 17 2009 125.JPG [ 246.74 KIB | Viewed 908 times ]

The board is 138 x 41 cm made from two layers of 1/4" AirCell Polyester foam sheets from Polyumac. The bottom skin is 3 layers of 5 oz glass with a fabric layer skinned by a layer of 1.5 oz. glass. The top is 4 layers of 5 oz with fabric and skin glass. There is about 4-5 cm of rocker and a single concave on the bottom. The handle is free hand cut from a sheet of 1 inch thick foam and covered with a carbon/glass braided sleeve.

Attachment:

IMG_2227.JPG [ 104.96 KIB | Viewed 900 times ]

Attachment:

IMG_2242.JPG [ 90.43 KIB | Viewed 896 times ]

Attachment:

IMG_2243.JPG [ 102.73 KIB | Viewed 897 times ]

The inserts are 3/8" aluminum that I drilled with a tap hole and back filled with candle wax. After the board was finished I drilled out the wax and tapped the threads in place. I filled the fin support holes with thickened glass filled epoxy and drilled them once the board was complete.

Attachment:

IMG_2244.JPG [ 80.39 KIB | Viewed 895 times ]

Attachment:

IMG_2246.JPG [ 82.75 KIB | Viewed 893 times ]

Attachment:

IMG_2248.JPG [ 91.28 KIB | Viewed 896 times ]

The first step was to lay up the bottom skin and first foam sheet against the rocker table (which I covered with a mylar sheet). Then epoxied the top foam layer in place. Then filled the edges with thickened epoxy and layed up the top glass layers. This filled in the gaps between the layers creating the rail.

Attachment:

IMG_2255.JPG [ 114.76 KIB | Viewed 896 times ]

Attachment:

IMG_2260.JPG [ 111.84 KIB | Viewed 896 times ]

Attachment:

Jan 17 2009 083.JPG [ 127.12 KIB | Viewed 899 times ]

Attachment:

Jan 17 2009 086.JPG [ 158.45 KIB | Viewed 900 times ]

Attachment:

Jan 17 2009 092.JPG [ 128.16 KIB | Viewed 899 times ]

Attachment:

Jan 17 2009 093.JPG [ 163.53 KIB | Viewed 899 times ]

Attachment:

Jan 17 2009 094.JPG [ 154.21 KIB | Viewed 896 times ]

Thanks again for all the great input here.
Derek

kitehok · **Joined:** Mon Apr 14, 2008 7:47 pm **Posts:** 145

That board is money!!

How did you do the graphics, rice paper? 1 piece or sections? Without spending a fortune at a print shop, I've yet to find a method to print a full board graphic.

ddeville · **Joined:** Mon Jan 26, 2009 12:28 am **Posts:** 2

The graphic is printed fabric (cotton I assume) that is trapped under a thin layer of fiberglass. I just went to the fabric store and found patterns that I liked.

BTW, the board rides real nice. I only got about an hour on it, but it felt real good. Tracked upwind nice and the flex really ate up landings.

Derek

liv2surf · **Posted:** Mon Feb 16, 2009 5:29 pm

impressive.

schmoe · **Joined:** Fri Jul 08, 2005 3:42 am **Posts:** 1026

That is one cool looking board. Can you please explain how you did the rail again?

Toby · **Posted:** Tue Mar 17, 2009 2:31 pm

very cool job!

I guess now you will do every month a new one just so your design ideas can become reality? :thumb:

Funny, in the beginning of the shaping process it reminded me of the good old pickle fork ;-)

Paper Chaser - First Board - Thanks to the list!!!

Who is online