Contact   Imprint   Advertising   Guidelines

Pumps for vacuum bagging

Here you can exchange your experience and datas about your home build boards
jmanindo
Rare Poster
Posts: 8
Joined: Sat Dec 13, 2008 7:19 am
Local Beach: Lincoln City Oregon
Favorite Beaches: The bay
Style: Old school surf
Gear: 11 # 7m Slinshot TD's, Slinshot twin tip
Brand Affiliation: None
Has thanked: 0
Been thanked: 0

Pumps for vacuum bagging

Postby jmanindo » Wed Dec 15, 2010 2:02 am

I have read through the posts and didn’t see any threads on this. Can anyone comment on the use of a shop vac for vacuum bagging a kiteboard? I have a 2hp shop vac. I have done some research and have read some opinions saying that it will work but the vacuum force is far lower than a regular vacuum pump. I have also read about converting tire pumps, air compressors and refrigerator pumps into vacuum pumps. Anybody have success bagging a kiteboard with a shop vac? I’m trying to avoid the $300 +/- cost of a regular pump. Thanks.

Steve

zfennell
Very Frequent Poster
Posts: 975
Joined: Wed Nov 20, 2002 1:00 am
Brand Affiliation: None
Location: rhode island
Has thanked: 0
Been thanked: 0

Re: Pumps for vacuum bagging

Postby zfennell » Wed Dec 15, 2010 3:23 am

if going cheap, do the fridge compressor.
its the only real vacuum source (of the ones you mention) capable of getting respectable vacuum
7-10 psi vacuum (4 psia)

look up plans on joe-woodworker .com

buy one of their vacuum switches so you dont burn out the pump or the house.

that, plus a cheap resevoir out of pvc pipe and a few bits of wire and tubing and you are good to go.

bill

Nico
Very Frequent Poster
Posts: 2645
Joined: Sun Jan 06, 2002 1:00 am
Local Beach: private kitebeach on my doorstep,
Le Morne.
Style: wave
Gear: Drifter kites, wave boards
Brand Affiliation: Cabrinha, naish
Location: Mauritius, waterman since 1960
Has thanked: 0
Been thanked: 0

Re: Pumps for vacuum bagging

Postby Nico » Wed Dec 15, 2010 4:58 am

Hi Bill.
Got any links where one can understand the process and required tools fully ?
I would like to give this a try too and am pretty handy with my hands
Nico.

zfennell
Very Frequent Poster
Posts: 975
Joined: Wed Nov 20, 2002 1:00 am
Brand Affiliation: None
Location: rhode island
Has thanked: 0
Been thanked: 0

Re: Pumps for vacuum bagging

Postby zfennell » Wed Dec 15, 2010 2:42 pm

Nico wrote:Hi Bill.
Got any links where one can understand the process and required tools fully ?
I would like to give this a try too and am pretty handy with my hands
Nico.
http://www.joewoodworker.com/veneering/welcome.htm

http://www.dream-models.com/eco/vacuumpump.html

the last link shows all the getto style bits and pieces, but joe woodworkers vacuum switch is much better/easier than the automotive distributer style.
to each his own but,
that's all there is to it.
-bill

jmanindo
Rare Poster
Posts: 8
Joined: Sat Dec 13, 2008 7:19 am
Local Beach: Lincoln City Oregon
Favorite Beaches: The bay
Style: Old school surf
Gear: 11 # 7m Slinshot TD's, Slinshot twin tip
Brand Affiliation: None
Has thanked: 0
Been thanked: 0

Re: Pumps for vacuum bagging

Postby jmanindo » Wed Dec 15, 2010 7:02 pm

Bill. It looks like I can pick up a used pump on ebay for roughly the same amount that I would invest in converting a fridge pump. Thanks for the input.

Steve

User avatar
foam-n-fibre
Frequent Poster
Posts: 491
Joined: Tue Jan 02, 2007 11:50 pm
Gear: DIY boards and OR kites
Brand Affiliation: None
Location: Ottawa, Canada
Has thanked: 1 time
Been thanked: 8 times

Re: Pumps for vacuum bagging

Postby foam-n-fibre » Thu Dec 16, 2010 9:25 pm

I've built lots of boards with a shop vac. Started out with a shop vac, got a fridge compressor, and then when it died I went back to the shop vac. Haven't got the new fridge compressor going yet.

If you are trying to really move a lot of resin then you need the high vac like a fridge compressor or better. If you want clamping force, then a shop vac is sufficient. Scroll down the index page to the link for the videos I posted on how to build a board. Using the technique I'm using there, I can't tell the difference in the end result for either type of pump. But, I didn't go for toally max vacuum with my fridge compressor anyway, I was not trying to dry the board out that much.

Peter

mattthieu
Medium Poster
Posts: 135
Joined: Fri Apr 06, 2012 2:01 pm
Local Beach: none so far
Favorite Beaches: snowy fields around !!
Style: snow kite ski for now !!
Gear: some foils, and two new LEI for this summer !
Brand Affiliation: none yet !!héhé
Has thanked: 0
Been thanked: 0

Re: Pumps for vacuum bagging

Postby mattthieu » Tue Apr 23, 2013 10:07 pm

hi

what kind of shop vac woud be needed ? i mean at least what force ?

would like to try first board without spending money and time on a vacum pump !!


Return to “Gear Builders”

Who is online

Users browsing this forum: No registered users and 53 guests