Here you can exchange your experience and datas about your home build boards
-
TomW
- Very Frequent Poster
- Posts: 3585
- Joined: Wed Oct 05, 2005 6:43 pm
- Kiting since: 2001
- Local Beach: Vejbystrand, Lomma
- Gear: TW Surfboards hydrofoil board 110
Gong Veloce M, 100cm carbon mast
Ozone Hyperlink V1 7m
Hyperlink V2 9m, 13m
Concept Air Wave 4,5m
- Brand Affiliation: None
- Location: Sweden
-
Has thanked:
53 times
-
Been thanked:
193 times
Postby TomW » Sun Jan 21, 2018 7:40 pm
Hi,
While I'm working on designing a wing to fit my moses fuselage, which is somewhat driving the design, I am starting to think about just making a fuselage and bonding the wings to the fuselage and attach it to a standard aluminium strut.
What do you think of the idea of using standard carbon tubes? I can get a 20mmx18mm tube, and glue a 18x16 mum inside, then a 16x14 to give 20 OD x 14 ID, 3mm walls. Then I could fill center to allow screwing to the Alu strut. the ends I would fill and shape, bonding the wings to the fuselage. The wings I would design with " seats" for the cylindrical fuselage.
The tubes are not super cheap, about 60 euros together for 1m lengths.
The advantage is i get accurate cylinder to create seat for wings and control AoA setting while bonding.
I can also get a 12mm solid CF UniD rod, and glue 14 and 16mm tubes over it.
Would this be sufficiently stiff and strong?
-
thewindego
- Frequent Poster
- Posts: 259
- Joined: Wed Jan 18, 2017 3:13 am
- Local Beach: Wolfe Island
- Gear: core and windego boards
- Brand Affiliation: None
-
Has thanked:
29 times
-
Been thanked:
38 times
-
Contact:
Postby thewindego » Sun Jan 21, 2018 9:56 pm
Seems like a solid plan to me either way. But may cost quite a bit more than just rolling your own and then you can include the strut connection in the fuse.
-
plummet
- Very Frequent Poster
- Posts: 6819
- Joined: Sat Aug 29, 2009 11:25 pm
- Local Beach: EE
- Favorite Beaches: NZ
- Style: Terrain riding
- Gear: Old wornout ozone.
Plummet hydrofoil and mutant
- Brand Affiliation: None
-
Has thanked:
11 times
-
Been thanked:
224 times
Postby plummet » Mon Jan 22, 2018 2:15 am
My gut is that it's overkill. I recon 18x1mm might be enough. I say get the 18x 1 do a flex test compared to your current. If needed add the 16x1.
-
downunder
- Very Frequent Poster
- Posts: 2821
- Joined: Mon Jul 01, 2013 7:16 am
- Gear: building my own
- Brand Affiliation: None
- Location: Perth, Australia
-
Has thanked:
153 times
-
Been thanked:
160 times
Postby downunder » Mon Jan 22, 2018 3:02 am
I've broken my tube in test phase, 22/20mm, this one (at the bottom):
http://kiteforum.com/viewtopic.php?f=19 ... 8&start=80
3mm walls might be ok tho, but man, why would you pay 60E for that? I've paid 10$ for the above tube, so it's ok as one off.
A wood piece slightly tapered from 28mm to 20 is way way more stronger than carbon tube when wrapped with carbon with same walls. And it floats. Plus, you not buying 1m carbon tube and using 70cm...I can stand on that (60kg) with only one UNI layer around the wood (length wise), and will slap one more 45/45 biax to accommodate for torsion.
Cost? Cheap as chips. Duno, 20$? That's coz wood is expensive here, like, just that wood piece was 15$, plus carbon...
-
plummet
- Very Frequent Poster
- Posts: 6819
- Joined: Sat Aug 29, 2009 11:25 pm
- Local Beach: EE
- Favorite Beaches: NZ
- Style: Terrain riding
- Gear: Old wornout ozone.
Plummet hydrofoil and mutant
- Brand Affiliation: None
-
Has thanked:
11 times
-
Been thanked:
224 times
Postby plummet » Mon Jan 22, 2018 6:58 am
I agree with downunder. Go get a bit of wooden dowl wrap and bag it. Will be way cheaper and strong as.
-
TomW
- Very Frequent Poster
- Posts: 3585
- Joined: Wed Oct 05, 2005 6:43 pm
- Kiting since: 2001
- Local Beach: Vejbystrand, Lomma
- Gear: TW Surfboards hydrofoil board 110
Gong Veloce M, 100cm carbon mast
Ozone Hyperlink V1 7m
Hyperlink V2 9m, 13m
Concept Air Wave 4,5m
- Brand Affiliation: None
- Location: Sweden
-
Has thanked:
53 times
-
Been thanked:
193 times
Postby TomW » Mon Jan 22, 2018 4:39 pm
Ok thanks.
That's 60E for 3 tubes. If I go to 2 tubes I get down to about 40E.
My plan was to 3d print a spacer between the cylinder fuse and the aluminum mast. Both surfaces are accurate so easy to do.
And I could just embed some stainless inserts into the filked carbon tube and screw the wings to it.
Get your point about making my own.
-
plummet
- Very Frequent Poster
- Posts: 6819
- Joined: Sat Aug 29, 2009 11:25 pm
- Local Beach: EE
- Favorite Beaches: NZ
- Style: Terrain riding
- Gear: Old wornout ozone.
Plummet hydrofoil and mutant
- Brand Affiliation: None
-
Has thanked:
11 times
-
Been thanked:
224 times
Postby plummet » Mon Jan 22, 2018 6:35 pm
TomW wrote: ↑Mon Jan 22, 2018 4:39 pm
Ok thanks.
That's 60E for 3 tubes. If I go to 2 tubes I get down to about 40E.
My plan was to 3d print a spacer between the cylinder fuse and the aluminum mast. Both surfaces are accurate so easy to do.
And I could just embed some stainless inserts into the filked carbon tube and screw the wings to it.
Get your point about making my own.
If its easy and you want to try it then give it a go. I've changed my mind on my suggestion, 20x1mm tube would be better. Then perhaps consider 18x1 insert from fron wind to just past the mast. The rear stab doesnt need the same strength/stiffness as the mast to front wing connection.
At the risk of telling you how to suck eggs, Mount the front wing on the bottom of the fuse and the rear wing on the top. This means the water will be pushing the wings into the fuse and not trying to tear the wings off the fuse... Its much lower force on the bolts if you do it this way!!!..... It might be obvious, however some major brands miss this design feature. I was looking at one (Ketos i think). The rear wing was bolted on the bottom with 2 x 5 or 6mm bolts. On the foil i was looking at the bolts had come loose. Stupid design!
-
tegirinenashi
- Very Frequent Poster
- Posts: 815
- Joined: Wed Aug 27, 2014 3:29 am
- Local Beach: 3rd Ave
- Gear: Bates 4000, Dominator MX-10
- Brand Affiliation: None
-
Has thanked:
33 times
-
Been thanked:
36 times
Postby tegirinenashi » Mon Jan 22, 2018 7:36 pm
If you slide and glue smaller diameter tubes inside each others, then you don't need them 1 m long. And 50 cm ones are much much less expensive. For 70 cm long fuse even 40 cm tubes would be OK. Then, I would sculpt the wings fuse connection areas with some additional layers of carbon, wrap it into couple of carbon sleeves and call it a day. (Easier said that done, of course, my fuse project took forever to complete).
-
TomW
- Very Frequent Poster
- Posts: 3585
- Joined: Wed Oct 05, 2005 6:43 pm
- Kiting since: 2001
- Local Beach: Vejbystrand, Lomma
- Gear: TW Surfboards hydrofoil board 110
Gong Veloce M, 100cm carbon mast
Ozone Hyperlink V1 7m
Hyperlink V2 9m, 13m
Concept Air Wave 4,5m
- Brand Affiliation: None
- Location: Sweden
-
Has thanked:
53 times
-
Been thanked:
193 times
Postby TomW » Mon Jan 22, 2018 9:15 pm
Thanks guys.
I could do this: Take a 680mm long 20mmx18mm tube and insert a 300mm 18x16mm tube into it as re-inforcement for the front wing and strut connection.
This is the tube i would buy- its my normal supplier- but i might be able to find another source-
- woven-finish-carbon-fibre-tube-20mm-17mm.jpg (14.1 KiB) Viewed 3156 times
I would fill the fuselage where wings and strut would be attached. And i could easily put M6x15mm 318 SS inserts into the fuselage for the wings. Then i would design a " spacer" for the fuse on top of front wing and bottom of rear wing and 3D print it. The spacers would form the ends of the fuselage too.
It does not sound that difficult. Advantage is i can get a Slingshot alu strut pretty good price, and i can easily try out this entire set up on a spare board. Screwing the wings on lets me modify the wings and change the AoA.
Now i have to find the time to do it...
-
airsail
- Very Frequent Poster
- Posts: 692
- Joined: Mon Jun 22, 2009 8:57 am
- Weight: 80kg
- Local Beach: Queens Beach North, Queensland, Australia
- Favorite Beaches: Queens North, I don’t travel much
- Style: Foiling
- Gear: Sonic 3 15mtr, Soul 10 mtr, BRM Clouds 8, 6.2, 4.8, 3.7
Lift, Naish and Levitaz foils
Carbonco and home build boards
Ozone and Duotone wings
Naish Hover 95 foilboard
- Brand Affiliation: None
- Location: Australia
-
Has thanked:
342 times
-
Been thanked:
172 times
Postby airsail » Mon Jan 22, 2018 11:02 pm
An easy option is to forget the tube, go the dowel. Sink your nuts into the dowel then rather than try and vac bag carbon, use carbon sleeve,
http://www.playwithcarbon.com/products/ ... leeve.html,
It expands when pushed together, slide over the dowel, apply the resin, then pull the ends tight. Add a few layers and when dry apply a filler coat, gives a nice professional finish.
Return to “Gear Builders”
Who is online
Users browsing this forum: No registered users and 149 guests