Contact   Imprint   Advertising   Guidelines

Re-sleeving kite lines...is it safe?

Forum with lots of safety info - a must for newbees


User avatar
Dj A-Ron
Frequent Poster
Posts: 235
Joined: Fri Jul 24, 2009 5:29 pm
Kiting since: 2009
Local Beach: Cass Lake MI
Port Huron MI (Lake Huron)
Metro Beach MI (Lake St. Clair)
Harsens Island MI (Lake St. Clair)
Favorite Beaches: Tawas MI (Lake Huron)
Oscoda MI (Lake Huron)
Little Sable Point MI (Lake Michigan)
The Flats (Key West)
Anywhere in Cape Hatteras
Kite Beach (Maui)
La Ventana (Mexico)
Barkers (Grand Caymen)
Style: Freeride/Freestyle
Gear: Kites: Epic Renegade 9m 3G, Airush Lithium 12m & 14m, Blade Fat Lady 17m

Boards: Epic Droid, Oxygen, Spartan, Airush Cypher 5'6"
Brand Affiliation: None
Location: Michigan

Re-sleeving kite lines...is it safe?

Postby Dj A-Ron » Fri Jul 24, 2009 9:19 pm

I read an article in The Kiteboarder magazine about cutting your lines down and re-sleeving them....I'm actually not cutting my lines down but I did snap a line about 3 feet from the leader line of the bar and was wondering if its possible and more importantly SAFE to re-sleeve your kite lines? I have another bar so I'm still able to take sessions but am a little low on funds and was hoping to getahold of one of these kits to fix my backup bar. If it is safe to re-sleeve the lines, do any of you know what I should look for...or any websites I should visit to purchase one of these kits?

Thanx for any help. :thumb:

User avatar
sflinux
Frequent Poster
Posts: 407
Joined: Tue Aug 02, 2005 4:23 pm

Re: Re-sleeving kite lines...is it safe?

Postby sflinux » Sat Jul 25, 2009 6:27 am

I've broken quite a few lines in the surf (usually breaks at the stock sleeve). I resleeve them with no worries. Just use 100% polyester resin over the dacron sleeve. I use a sewing machine with a zigzag stitch, double backed to lock the stitch. You can use something like amsteel (near the bar) or q-line to extend the line that was shortened to equal the other lines.

User avatar
matt at jibe's
Rare Poster
Posts: 37
Joined: Sun Sep 06, 2009 10:08 am
Kiting since: 1999
Local Beach: mui ne viet nam
Favorite Beaches: mui ne beach; hon rom/ Mack beach (viet nam)
enshuu beach in Hamamatsu, Japan
Tenryuugawa beach in Hamamatsu, Japan
Style: snowboard/old school
Gear: Airush Flow. Lithium ,, RRD Hypertype etc etc
boards: f-one Fluid, Trax, airush, tbk, Hatori, various
Brand Affiliation: chief instructor at Jibe's in Mui Ne, Viet Nam
we carry airush/f-one/tbk/underground/dakine/prolimit
Location: Mui Ne, Viet Nam
Contact:

Re: Re-sleeving kite lines...is it safe?

Postby matt at jibe's » Mon Aug 09, 2010 7:31 am

err... a few years ago I got lazy (I've cut down and re-attached a lot of lines over the years) and started to attach my lines at the bar ends without re-sleeving them at all (the old Q-power lines spoiled me I guess). Just fold over the last 12cm of line or so and then make a loop using the figure 8 knot. When you cut down your lines, you need to keep the sleeving at the kite ends so you can attach and detach to the pigtails easily. But at the bar end, whether I've attached the unsleeved ends to a knotted leader line or to a metal ring, I've yet to see a line break there. Seen them break plenty in other places though. Sflinux says that he has seen lines usually break at the stock sleeve, and so have I. Sometimes I wonder if the holes needed to sew a sleeve onto the lines weaken them at that point.

Go ahead and cut your other lines shorter to match the broken one and enjoy kiting on shorter lines... see my post at viewtopic.php?f=1&t=2365823

To do this, put a screwdriver through the loops of your lines at the kite end, stab it in the ground, pull all the lines tight, then bend them all over in the same place. Hold on to where the bend is and then make your loops there, final check your lengths before cutting off the excess. That way all the lines are the same length. It doesn't really matter if your loops are of a little different size because the length from old loop end to the one of the new loop you've just made will be the same on all lines.

Oh, and be careful about using and re-using your lines this way--- eventually as the lines get older they will get weaker. When I break a line on my own kite under normal wear, I replace all the lines, as I've learned that another break on the same set of lines is soon to follow!


Return to “Safety”

Who is online

Users browsing this forum: No registered users and 3 guests