*


All times are UTC + 1 hour



Post new topic Reply to topic
 [ 6 posts ] 
Author Message
 Post subject: New carbon board
PostPosted: Thu Sep 09, 2010 4:04 pm 
Offline
Rare Poster

Joined: Thu Aug 12, 2010 8:18 pm
Posts: 18
Hi,

I have just finish my second carbon building project. Unfortnatly I haven't really tested yet, because last time I was surfing the waves were to big for me trying a new board, so I sticked to an old well know board. The overall dimension of this new board is 140x42cm, a flat-medium rocker and medium curved outline, just an everyday board. The weight of the board without straps, pads and fins is 1,8kg, so thats fine. I have shaped with pretty flexible tips, starting outside the straps, and a more stiff body section between the straps. Now I have a light wind TT, an everyday TT, and the next I'm going to build is a wave TT, with much more rocker, and much more rounded tips, smooth smooth rails.

Kind regards from Denmark
Lars
Image
Image
Image
Image
Compared with my light wind tt
Image


{ SHARE_ON_FACEBOOK } { SHARE_ON_TWITTER } { SHARE_ON_ORKUT } { SHARE_ON_DIGG } { SHARE_ON_MYSPACE } { SHARE_ON_DELICIOUS }
Top
Profile
 Post subject: Re: New carbon board
PostPosted: Thu Oct 21, 2010 8:38 pm 
Offline
Medium Poster

Joined: Wed Feb 25, 2009 12:40 am
Posts: 91
NIce Board! Does the Carbon allow the board to flex at all?


Top
Profile
 Post subject: Re: New carbon board
PostPosted: Sat Oct 30, 2010 7:27 pm 
Offline
Rare Poster

Joined: Thu Aug 12, 2010 8:18 pm
Posts: 18
I have to be honest, it is not 100% carbon. It is glass fiber / carbon fiber combination. But you can make a carbon board as flexible as you want, it is just question regarding the thickness of the core. The current board has a pretty stiff center body with flexibel tips. I have had some problems with this board, as it wanted to make spin out all the time if I wasn't very careful how place pressure on the back foot. But after changing the outline, the rails and added some extra rocker it has turned into a really nice board, and still bloody fast

ciao
Lars


Top
Profile
 Post subject: Re: New carbon board
PostPosted: Thu Jun 30, 2011 2:58 am 
Offline
Rare Poster

Joined: Wed Jul 28, 2010 1:29 am
Posts: 37
your board looks awsome u are doing great i would like to give u a few things i do with boards i hope they are of use to u first on a twintip wave board one and one quarter inch rocker is all u need any more will begin to lose low wind performance but for a realy killer wave TT make the bottom quarter inch CONVEX bottom this makes the board want to rol from one side to another which is a must in wave riding and it greatly smoothes out the overall ride most of the new boards are going this way but they do it with a spine in the middle either works great. hope this is of value keep riding your own creations for other ideas look at wainman JOKE


Top
Profile
 Post subject: Re: New carbon board
PostPosted: Thu Jun 30, 2011 8:47 am 
Offline
Frequent Poster
User avatar

Joined: Fri Oct 15, 2010 9:55 am
Posts: 384
Location: St Mary's Bay
Hi, I’m not a board builder but am a keen Kiteboarder. I went on a resent health & safety course, they spoke about Carbon fibre, and according to them Carbon fibre is the new Asbestos. Obviously it will be years down the line before people see the full effects of inhaling Carbon Fibre dust but I am sure a lot of people have been using this stuff totally unaware of its damage to health. Sorry guys, didn’t want to hack into the thread, just saw the heading and thought I’d chip in. Great looking board by the way :thumb:


Top
Profile
 Post subject: Re: New carbon board
PostPosted: Thu Jun 30, 2011 5:50 pm 
Offline
Very Frequent Poster

Joined: Thu Jun 05, 2003 3:37 am
Posts: 2372
Well, yes, you need to wear a mask and clean up if you sand into carbon.
Not that fiberglass is good for your lungs either....
Fortunately building kiteboards involves very little sanding into the fiber layers, unless you screw something up. The the fibers stay safely embedded in epoxy.


Top
Profile
Display posts from previous:  Sort by  
Post new topic Reply to topic
 [ 6 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group