*


All times are UTC + 1 hour



Post new topic Reply to topic
 [ 3 posts ] 
Author Message
 Post subject: Help needed for low-wind twintip
PostPosted: Wed Mar 14, 2012 7:10 pm 
Offline
Rare Poster

Joined: Thu Mar 03, 2011 12:04 pm
Posts: 10
Hi guys!!!!

I am trying to built my first low-wind (low cost :thumb: ) twin-tip. I am 85Kg and I need it for 9 - 12 knots with a 12m kite.

I will use 8mm marine plywood as core and 120g/cm fiberglass. Please advise:

1) optimum size of board (I am thinking of 155 x 45 ??? :o )

2) How many layers of the above fiberglass ??? (please specify top and bottom respectively). Need to last more than 1 summer :D :D but not be heavy as a brick !!!

3) Please advise about shape: Square tips or round tips?? Any favourite known board design which I could follow???

4) Is rocker at the tips needed ??? (approx. 2-3cm)

5) Is concave at the bottom needed???

thank you in advance!!


{ SHARE_ON_FACEBOOK } { SHARE_ON_TWITTER } { SHARE_ON_ORKUT } { SHARE_ON_DIGG } { SHARE_ON_MYSPACE } { SHARE_ON_DELICIOUS }
Top
Profile
 Post subject: Re: HELP NEEDED FOR LOW-WIND TWINTIP
PostPosted: Wed Mar 14, 2012 10:03 pm 
Offline
Very Frequent Poster

Joined: Wed Nov 20, 2002 1:00 am
Posts: 826
Location: rhode island
120 g/m^2 ( approx 4oz)

2 layers glass on top
one layer 8 mm plywood
2 layers on bottom

maybe a bit soft.
but i would try first and add more later if you choose.
flat and floppy is fine for a light air board.
no need for rocker or concave unless you'd like to experiment.
perhaps soak it or sail it then clamp it against some bricks/blocks in the sun to coax some shape into it.
paint it once you want it to stop taking on water and protect edges and laminating resin



a 4 x 8 sheet of ply will net a few boards.
i dont really think this effort is worth the added expense of marine ply.
A/C plywood siding. or even luan door skins will work.
you get to choose.


if you choose to bond 2 layers of 8mm , you can mold in rocker and concave and get away with less glass.
0-1 layer of 120g glass on top and bottom.

straight sides, rounded tips, fins in the corners (or none)
155 x 45 sounds like a good place to start.
if you make it over sized, dont think twice about just cutting some off to suit your needs.

have fun.
-bill


Top
Profile
 Post subject: Re: Help needed for low-wind twintip
PostPosted: Fri Mar 16, 2012 9:37 pm 
Offline
Rare Poster

Joined: Tue Feb 07, 2012 8:56 pm
Posts: 26
My advice would be not to use plywood. Glue some 300-400 kg/m3 wood strips 8x20x1500 instead.
Total of 280-350 g/m2 higher grade glass fabric (unidirectional and biaxial should dominate) on top and the same on bottom would be soft and fine. Marine plywood will add 1kg or more to your huge board. 3-4 cm continous rocker and 8 mm concave in the middle section for better plannig . Bend a core twice more lenghtwise before epoxy is cured.
I have made few boards of wood only in the past. 25mm thickness was very soft and comfortable. The latest twintips where 5 mm core with composite skins and they were not so soft... Most kiteboards waste weight on cores mainly. The second advice would be not to use more than 90 g/m2 top and 70 g/m2 bottom of fibers in the perpendicular direction on the board. I hardly manage to breake even thin cored boards with only 80 g/m2 top and 80g/m2 bottom perpendicular direction glass fibers. Some cracks developed on the top side in the middle section after heavy landings. My point was that you must use mainly unidirectional fibers. The core must resist only compresive forces between the skin layers basically. Unfortunately wood is most resistan to compression in lenghtwise direction... But in 8mm core it would be enough


Top
Profile
Display posts from previous:  Sort by  
Post new topic Reply to topic
 [ 3 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group