Here you can exchange your experience and datas about your home build boards
-
Bille
- Very Frequent Poster
- Posts: 4026
- Joined: Sun Sep 04, 2011 5:37 pm
- Local Beach: Lake Mohave
- Gear: Ozone Edge
- Brand Affiliation: Barz Optics
Jaybar Dynabar V7
-
Has thanked:
252 times
-
Been thanked:
189 times
Postby Bille » Tue Apr 03, 2012 6:01 pm
edt wrote:Wicker wrote:I was thinking of using stainless steel T nuts.
stainless steel t nuts work fine.
Yes SS works -- but make "SURE" it's the Real Stainless
and not that imitation Cheap Crap from ... !!
The way to tell is bring a magnet with Ya when you purchase it ;
real SS won't be affected by it.
Bille
-
zob
- Frequent Poster
- Posts: 476
- Joined: Tue Feb 24, 2009 1:43 pm
- Local Beach: Grado Pineta (IT), Fossalon (IT)
- Style: Freeride, strapless hooked-in
- Gear: FS S3 19m2 DLX, S3 CE 12m2 DLX & S4 8m2 DLX
Homemade Surf & Snow Boards
MBS Pro90
- Location: Iv.G.-Slovenia
-
Has thanked:
21 times
-
Been thanked:
3 times
-
Contact:
Postby zob » Wed Apr 04, 2012 7:41 am
Bille wrote:but make "SURE" it's the Real Stainless
and not that imitation Cheap Crap from ... !!
???
Look for EN 1.4404 (AISI 316L) material or higher.
-
Bille
- Very Frequent Poster
- Posts: 4026
- Joined: Sun Sep 04, 2011 5:37 pm
- Local Beach: Lake Mohave
- Gear: Ozone Edge
- Brand Affiliation: Barz Optics
Jaybar Dynabar V7
-
Has thanked:
252 times
-
Been thanked:
189 times
Postby Bille » Thu Apr 05, 2012 3:51 am
zob wrote:Bille wrote:but make "SURE" it's the Real Stainless
and not that imitation Cheap Crap from ... !!
???
Look for EN 1.4404 (AISI 316L) material or higher.
NO question Here --ZOB-- !!
In the USA, they sell this Crap SH*T from Chi**, & try to pass it for SS.
It will NOT hold-up in salt water & your gonna see a rusty stain after a
short while.
I'm saying : "bring a magnet with Ya & see if it affects the sellers product ;
if it's a Good grade of SS, the magnet will NOT affect it.
I have a bag of 1/4-20 T-nuts, that a magnet will do nothing to.
Bille
-
Wicker
- Rare Poster
- Posts: 16
- Joined: Fri Mar 23, 2012 12:08 am
- Local Beach: Blackstrap
- Style: Crashing and Dragging
- Gear: Flysurfer Unity 12m
- Brand Affiliation: None
- Location: Saskatoon, Saskatchewan
-
Has thanked:
0
-
Been thanked:
0
Postby Wicker » Tue Apr 10, 2012 10:25 pm
Sweet, I may have to look online as teh local Bolt Supply doesn't carry them. Also waiting on fins and just ordered the pads and straps today.
-
zfennell
- Very Frequent Poster
- Posts: 975
- Joined: Wed Nov 20, 2002 1:00 am
- Brand Affiliation: None
- Location: rhode island
-
Has thanked:
0
-
Been thanked:
0
Postby zfennell » Thu Apr 12, 2012 1:58 am
T-nuts are fine.
but if you can't find any locally, i'm sure there are other solutions.
remember, this is plywood and your 2 hours are up.
if your willing to poke a hole thru the board for a t-nut , a flat head screw countersunk from the bottom will work as well.
#10, stainless, with nuts and washers will be easy to find.
most hardware store also sell threaded inserts made from brass that can be screwed into the top side of the board .
but if time is short, you can get galvanized deck screws by the pound from just about anywhere.
did i mention this board is plywood?
no worries,
its all good.
-bill
-
Wicker
- Rare Poster
- Posts: 16
- Joined: Fri Mar 23, 2012 12:08 am
- Local Beach: Blackstrap
- Style: Crashing and Dragging
- Gear: Flysurfer Unity 12m
- Brand Affiliation: None
- Location: Saskatoon, Saskatchewan
-
Has thanked:
0
-
Been thanked:
0
Postby Wicker » Thu Apr 12, 2012 6:31 am
Hahaha, not really sure why I didn't think of that. That will likely be the route I go. Like you said, it's plywood.
-
gbleck
- Very Frequent Poster
- Posts: 546
- Joined: Mon Oct 08, 2007 4:39 am
-
Has thanked:
0
-
Been thanked:
0
Postby gbleck » Thu Apr 12, 2012 1:26 pm
Brass is the good stuff if you can find it. Expensive but strong and no rust.
-
JMF
- Frequent Poster
- Posts: 493
- Joined: Mon Sep 02, 2002 1:00 am
- Brand Affiliation: None
- Location: Teahupo'o, Tahiti
-
Has thanked:
4 times
-
Been thanked:
0
Postby JMF » Sun Apr 15, 2012 8:45 am
I'll sound off and say you can also use threaded stainless steel stand offs. This will be the closest you come to proper inserts just cut to size and your done. I used snowboard inserts bought from
www.snowboardmaterials.com T-nuts although they do work the coarse thread doesn't give you much bite and most of them will corrode over time depending on what material they are made of which is usually a plated mild steel.
I suppose it also depends how mush effort/cash you want to put into the project. Weigh your options.
-
Wicker
- Rare Poster
- Posts: 16
- Joined: Fri Mar 23, 2012 12:08 am
- Local Beach: Blackstrap
- Style: Crashing and Dragging
- Gear: Flysurfer Unity 12m
- Brand Affiliation: None
- Location: Saskatoon, Saskatchewan
-
Has thanked:
0
-
Been thanked:
0
Postby Wicker » Tue Jun 19, 2012 11:58 pm
Hey Guys, sorry for taking so long to give an update. I was waiting for parts, got busy and blah blah blah. Anyway I also made a board for my girlfriends birthday and so I'll throw the pics up while I'm finishing up my board. I am definitely building a rocker table for the next board. I also used West Systems 207 Epoxy to cover the boards. It was really nice to work with and I am pretty happy with the results.
-
Attachments
-
-
Return to “Gear Builders”
Who is online
Users browsing this forum: No registered users and 136 guests