|
| Author |
Message |
|
borist
|
Post subject: Re: smaler fins on a sector 60 ? Posted: Tue Apr 10, 2012 2:18 am |
|
 |
| Medium Poster |
Joined: Tue Apr 20, 2010 12:30 am Posts: 93 Location: San Diego, CA
|
mattthieu wrote: thanks a lot ! i'll check for the versions ! so you tell me, white botom is ok white and grey not ? lack off coating ?? Yes, solid white. Or ask for serial number (on the bottom of the tail). Last three digits should be higher than 100. First series (V1, patchy white/black) had issues with fin boxes. As far as I know, Airush replaced all boards with damage under warranty, including mine. Upgraded version was one with solid white paint (same blue/black design) and is commonly referred to as V1.5. That is the one I currently use. 
|
|
| Top |
|
 |
|
mattthieu
|
Post subject: Re: smaler fins on a sector 60 ? Posted: Wed Apr 11, 2012 11:08 pm |
|
 |
| Medium Poster |
Joined: Fri Apr 06, 2012 2:01 pm Posts: 63
|
|
just ordered it online, just got the last i think, solid white......
i will let you know soon !
|
|
| Top |
|
 |
|
mattthieu
|
Post subject: Re: smaler fins on a sector 60 ? Posted: Sat Apr 28, 2012 3:05 pm |
|
 |
| Medium Poster |
Joined: Fri Apr 06, 2012 2:01 pm Posts: 63
|
|
just got the board, actually a v2 60.
got for times the 24 cm fins tho, so, waiting to receive the smaller ones for the back before trying it !
sanded the fins likes explaned on the sector fin topic so they dont touch the botom of the board....
just, question for people with experience, ideal wind range for that kite, to give it a first try ?
kites awaiable are 9m and 14m, wanted to try 9m first a that one has better relanch..
winds from ????? to ??????
thanks
as i understand it drives like a windsurf ?
|
|
| Top |
|
 |
|
borist
|
Post subject: Re: smaler fins on a sector 60 ? Posted: Mon Apr 30, 2012 7:54 pm |
|
 |
| Medium Poster |
Joined: Tue Apr 20, 2010 12:30 am Posts: 93 Location: San Diego, CA
|
|
mattthieu, depends on your weight, type of kite, type of wind (steady vs gusty), water conditions (flat vs choppy) and of course, your skills. 14m kite should get you going from ~10-11 knots and up, 9m should follow quite shortly from ~13 knots, just need to move it aggressively to get going. I'm talking rather steady wind (if 10 knots is an average and lulls are low and longer, that might be a problem). As you get better with the board you'll be able to push the low end further.
Upper end is more about water conditions than anything else. As long as you can control the speed you can ride the board. Big, steep chop will be uncomfortable at speed and most likely, cause you to crash. For me the ideal wind range is 10 to 16 knots. More that 20 knots at full speed is as much about balls as about skills. You could ride it, but would you want to?
Cheers
|
|
| Top |
|
 |
|
Rbgar
|
Post subject: Re: smaler fins on a sector 60 ? Posted: Thu Jun 21, 2012 9:45 pm |
|
 |
| Frequent Poster |
Joined: Thu Nov 15, 2007 6:07 pm Posts: 281 Location: RI
|
|
i found some NSP inserts for FCS fins, trying Occy trailers with the smaller Sector fins fwd to see if she loosens up some to have fun in small surf light winds, stand by? What the hell playin with fins is fun and make huge differences
| Attachments: |

photo (37).JPG [ 288.37 KIB | Viewed 517 times ]
|
|
|
| Top |
|
 |
|
Rbgar
|
Post subject: Re: smaler fins on a sector 60 ? Posted: Sun Jun 24, 2012 1:41 pm |
|
 |
| Frequent Poster |
Joined: Thu Nov 15, 2007 6:07 pm Posts: 281 Location: RI
|
Huge difference Got out in 15knots and the board still went upwind fine but now carves better, much more fun in the waves. Deff worth getting the FCS inserts and playing with surf fins, it changes the board in a big way. Cheers
|
|
| Top |
|
 |
Who is online |
Users browsing this forum: No registered users and 1 guest |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
|
|
|