*


All times are UTC + 1 hour



Post new topic Reply to topic
 [ 30 posts ]  Go to page Previous  1, 2, 3
Author Message
 Post subject: Re: ozone edge 2013 racebar setup?
PostPosted: Tue Oct 16, 2012 7:45 pm 
Offline
Very Frequent Poster
User avatar

Joined: Wed Aug 24, 2011 11:39 am
Posts: 1021
I found a ruler


Top
Profile
 Post subject: Re: ozone edge 2013 racebar setup?
PostPosted: Tue Oct 16, 2012 7:48 pm 
Offline
Very Frequent Poster
User avatar

Joined: Wed Aug 24, 2011 11:39 am
Posts: 1021
Here is the pic with ruler


Attachments:
image.jpg
image.jpg [ 1.49 MIB | Viewed 2095 times ]
Top
Profile
 Post subject: Re: ozone edge 2013 racebar setup?
PostPosted: Tue Oct 16, 2012 8:13 pm 
Offline
Very Frequent Poster

Joined: Tue Oct 14, 2008 9:14 am
Posts: 616
Location: outer space
Hawaiis wrote:
Here is the pic with ruler
thx mate!


Top
Profile
 Post subject: Re: ozone edge 2013 racebar setup?
PostPosted: Sat Jan 26, 2013 4:13 pm 
Offline
Rare Poster

Joined: Wed Jan 02, 2013 7:40 pm
Posts: 5
Hi everybody,
Based on available picture it was tried to modify the ordinary Ozone bar, but appeared question related to the length of front lines. From the picture it looks that race bar depower length nearly twice longer in comparison to ordinary, meaning that during modification front lines to be shortened as compensation and for the obtaining exactly the same total length as it was before. Or such difference to be ignored.

.


Top
Profile
 Post subject: Re: ozone edge 2013 racebar setup?
PostPosted: Sat Jan 26, 2013 7:57 pm 
Offline
Very Frequent Poster
User avatar

Joined: Wed Aug 24, 2011 11:39 am
Posts: 1021
The picture is the factory race bar, if you increase the travel of the the depower, you will need to decrease the front lines according or just add pigtails to the rear lines.


Top
Profile
 Post subject: Re: ozone edge 2013 racebar setup?
PostPosted: Sat Feb 02, 2013 3:47 pm 
Offline
Rare Poster

Joined: Wed Jan 02, 2013 7:40 pm
Posts: 5
My modified race bar. Side lines and one center line has been extended. Original depower travel length was 170mm, after modification it remain the same. Believe that it should work.


Attachments:
modified bar.JPG
modified bar.JPG [ 56 KIB | Viewed 1610 times ]
Top
Profile
 Post subject: Re: ozone edge 2013 racebar setup?
PostPosted: Sat Feb 02, 2013 7:38 pm 
Offline
Very Frequent Poster
User avatar

Joined: Wed Aug 24, 2011 11:39 am
Posts: 1021
Your blue depower line is about half of the factory bar, I only get 7 inch total depower, which is about 180mm. This is a 4:1 system, so your total depower should be only half of 170mm.


Top
Profile
 Post subject: Re: ozone edge 2013 racebar setup?
PostPosted: Sun Feb 03, 2013 2:29 pm 
Offline
Rare Poster

Joined: Wed Jan 02, 2013 7:40 pm
Posts: 5
Thank you, now I realize that was taken wrong reference point.


Top
Profile
 Post subject: Re: ozone edge 2013 racebar setup?
PostPosted: Sun Feb 03, 2013 6:33 pm 
Offline
Rare Poster

Joined: Wed Jan 02, 2013 7:40 pm
Posts: 5
Second version. Not complete, but basic is done.


Attachments:
IMG_2283.JPG
IMG_2283.JPG [ 52.49 KIB | Viewed 1499 times ]
IMG_2281.JPG
IMG_2281.JPG [ 55.08 KIB | Viewed 1499 times ]
Top
Profile
 Post subject: Re: ozone edge 2013 racebar setup?
PostPosted: Wed May 15, 2013 10:42 am 
Offline
Frequent Poster

Joined: Mon Sep 27, 2004 7:35 am
Posts: 299
Does anybody know the name of the rope that Ozone uses for the trimline ? (The rope that goes through the clamcleat in the 1:4 cascade)

I have used Racing Sheet, Orion500, Globe 5000 and Ocean3000 but are not happy with any of them.

Thanks in advance


Top
Profile
Display posts from previous:  Sort by  
Post new topic Reply to topic
 [ 30 posts ]  Go to page Previous  1, 2, 3

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group