*


All times are UTC + 1 hour



Post new topic Reply to topic
 [ 7 posts ] 
Author Message
 Post subject: Re-finishing the top surface?
PostPosted: Sat Oct 05, 2013 4:36 pm 
Offline
Very Frequent Poster
User avatar

Joined: Thu May 31, 2007 12:41 pm
Posts: 650
Location: Montreal, Canada / NJ, USA
I need some advice about my board's top surface re-finishing. Basically it's a rather classy, wooden-deck Brunotti board. Problem is - after 2 seasons of not very abusive usage the top surface has got a little dull, not to mention all the nicks and indentations from large sand particles (or small rocks) under the pads. So since I really like that particular board and I really don't see what it can be replaced with in any near future (no known equivalents) I'm thinking about re-finishing the deck this winter.

What are my options?
a)sanding+marine epoxy coat+sanding+polishing
b)sanding+gel coat
c)some other method?

My requirements are:
-zero weight penalty
-surface must come out nice, shiny as new and durable

Any constructive feedback and suggestions will be greatly appreciated! Thanks guys!


{ SHARE_ON_FACEBOOK } { SHARE_ON_TWITTER } { SHARE_ON_ORKUT } { SHARE_ON_DIGG } { SHARE_ON_MYSPACE } { SHARE_ON_DELICIOUS }
Top
Profile
 Post subject: Re: Re-finishing the top surface?
PostPosted: Sat Oct 05, 2013 5:21 pm 
Offline
Very Frequent Poster
User avatar

Joined: Tue Dec 23, 2003 6:30 pm
Posts: 845
Location: Traverse City, MI usa
The problem is your not riding hard enough to break the board, and get a new one! :P
Wet sand the board apply some epoxy, and coat with poly to protect from UV, or just wet sand and coat with poly.


Top
Profile
 Post subject: Re: Re-finishing the top surface?
PostPosted: Sun Oct 06, 2013 2:53 pm 
Offline
Very Frequent Poster

Joined: Wed Nov 20, 2002 1:00 am
Posts: 916
Location: rhode island
remove straps, pads, fins,

assuming no structural defects..
deck is wood laminate with glass and clearcoat?

-lightly sand with 400 grit US wet or dry
(definitely dont want to sand into glass unless that needs repair. If so, glass repair get done first in another topic)

-wash, rinse and let dry.

find a good marine spar varnish,
polyurethane with lots of uv inhibiters
(something like epithanes, but i'm sure thre are others)

use a foam brush , lightly loaded, keep moving in one direction.
always brush from 'wet' edge onto dry part of board.

resist temptation to recoat wet areas.
let it all dry to see what you've got

wet sand with 600 grit US should fix lumpy areas,
othrewise atother coat after light sanding.

-bill


Top
Profile
 Post subject: Re: Re-finishing the top surface?
PostPosted: Mon Oct 07, 2013 6:27 pm 
Offline
Very Frequent Poster
User avatar

Joined: Thu May 31, 2007 12:41 pm
Posts: 650
Location: Montreal, Canada / NJ, USA
Thanks for the input guys! That's about what I was thinking. Checked out the available products and a good varnish like Bristol comes at a sensible cost which I can hardly justify given that it's only for cosmetics. No glass damage b.t.w. Had some nicks on the edges, but I do get these repaired with epoxy right away. Will see how rusty I'll get from not riding during the winter - might still do it anyways, but for now I'll just be riding harder! ))) :thumb:

What are good and durable varnishes for wooden decks that don't cost a leg?


Top
Profile
 Post subject: Re: Re-finishing the top surface?
PostPosted: Tue Oct 08, 2013 3:26 am 
Offline
Frequent Poster
User avatar

Joined: Mon Jul 01, 2013 7:16 am
Posts: 307
Location: Perth, Australia
I build my boards and always repaint before the season. Using only Goldspar Original varnish. You can see the shine here:

http://downunderbloghr.blogspot.com.au/

Not applying with a brush, just spreading with a credit card a few times. Or recently spraying with a Preval spray which is even better. Thin a varnish before spraying.

The above might be better if you have Brunotti with channels.

350g Goldspar ~AU$20.


Top
Profile
 Post subject: Re: Re-finishing the top surface?
PostPosted: Tue Oct 08, 2013 1:06 pm 
Offline
Very Frequent Poster

Joined: Wed Nov 20, 2002 1:00 am
Posts: 916
Location: rhode island
alexeyga wrote:
Thanks for the input guys! That's about what I was thinking. Checked out the available products and a good varnish like Bristol comes at a sensible cost which I can hardly justify given that it's only for cosmetics. No glass damage b.t.w. Had some nicks on the edges, but I do get these repaired with epoxy right away. Will see how rusty I'll get from not riding during the winter - might still do it anyways, but for now I'll just be riding harder! ))) :thumb:

What are good and durable varnishes for wooden decks that don't cost a leg?



most come in small quantities ( 1/2 pint or less) with good shelf life
but you could just give it to an auto detailer for 5 min.
i bet buffing wheel and polish will make it look pretty good, too


Top
Profile
 Post subject: Re: Re-finishing the top surface?
PostPosted: Wed Oct 09, 2013 5:55 pm 
Offline
Very Frequent Poster
User avatar

Joined: Tue Dec 23, 2003 6:30 pm
Posts: 845
Location: Traverse City, MI usa
I'm really partial to clear Minwax Fast-Drying Polyurethane. Your board is not a boat that is left out 24 7 in the elements, so you really dont need the UV protection of Spar Poly, poly is way more UV resistant than Epoxy, and a barrier coat of any Poly should be good. My boards stay shiny for years.
Another option if you want a very shiny UV resistant coating, is a Automotive Clear Coat, it to, is fast drying and very shiny and Hard. They use Automotive paint to revitalize boat hulls almost like new.


Top
Profile
Display posts from previous:  Sort by  
Post new topic Reply to topic
 [ 7 posts ] 

All times are UTC + 1 hour


Who is online

Users browsing this forum: No registered users and 3 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group