Contact   Imprint   Advertising   Guidelines

DIY Home Made wooden Hydrofoil fins

A forum dedicated to Hydrofoil riders
Europ2
Frequent Poster
Posts: 473
Joined: Wed Mar 01, 2006 7:51 pm
Brand Affiliation: None
Has thanked: 14 times
Been thanked: 7 times

Re: DIY Home Made wooden Hydrofoil fins

Postby Europ2 » Wed Nov 13, 2013 9:27 pm

Mini Tuttle box blueprints are difficult to find.
NSP mini tuttle fin boxes are around 9cm long x 1.8 cm high x 1.3cm wide

If somebody has the blueprints+ dimensions, pls post here.
http://www.windsurfingfins.co.uk/prod5. ... rod_anchor

The Mini-Tuttle foilboard struts plug can be casted in one of the mini tuttle boxes as described bellow.

Here is my favorite link from Reystos.about Tuttle box.
http://www.geocities.ws/reystos/fin_making/index.htmll

(From the legendary http://www.geocities.ws/reystos/ :jump: and his SW for designing kites - some 12 years ago)
Although I cannot guarantee the results of this method, you can use a finbox to cast the base. This applies to Powerbox and Tuttle (+Deep Tuttle) fins. Trimbox fins can't be cast in their box as the box doesn't have the fin's shape. Make sure your finbox is waxed well and the screw holes are sealed with plasticine before casting with thickened resin or epoxy putty. You will also have to figure out a way to keep your fin vertical in respect to the level of the finbox. Another detail you will need to figure out is how to place the screw nuts in position, since casting with the screws in place is no easy task.
Image

Fin designer still available here: http://www.geocities.ws/reystos/fin_designer/index.html
I cannot open the Zip archive (old Win 95/98/ME Zip version not compatible xith Win VISTA, 7 Zip ? 32bit vs 64bit ??)

For our 100 or 110 mm chords, the 160mm box will clearly be over dimensionned.

3G composites (Ketos by Orana) have developped their own box based on morse cone sections around 5 degrees (versus 6 for the tuttle box wall).
AlpineFoil use this setup on the 5.0 board version with the Courtesy of 3G composites.

Johnny Rotten
Very Frequent Poster
Posts: 501
Joined: Thu Dec 04, 2008 1:50 am
Style: Surf and wake
Gear: Vegas
Torch
Neo's
Hand made boards of pure excellence
Brand Affiliation: None
Location: No fixed address
Has thanked: 10 times
Been thanked: 29 times

Re: DIY Home Made wooden Hydrofoil fins

Postby Johnny Rotten » Wed Nov 13, 2013 11:13 pm

Although I cannot guarantee the results of this method, you can use a finbox to cast the base. This applies to Powerbox and Tuttle (+Deep Tuttle) fins. Trimbox fins can't be cast in their box as the box doesn't have the fin's shape. Make sure your finbox is waxed well and the screw holes are sealed with plasticine before casting with thickened resin or epoxy putty. You will also have to figure out a way to keep your fin vertical in respect to the level of the finbox. Another detail you will need to figure out is how to place the screw nuts in position, since casting with the screws in place is no easy task.
This works well.
http://kiteracing.com/Pot_a_Fin.html
If you look into the background of some of the rista fins videos you can see a similar jig so I suspect this is (sorta) how the pros do it.

I would recommend adding a second nut onto the bolt you put in. so that is fully encased. in the epoxy and cannot pull out.

Epoxy/milled glass powder can work as a casting agent, if you don't have a urethane kicking around. I also recommend locktite frekote as a mold release, If you can't get the crap these guys are using wax doesn't work well on the best of days and is miserable to apply to the inside of a fin box.

User avatar
Hawaiis
Very Frequent Poster
Posts: 1375
Joined: Wed Aug 24, 2011 11:39 am
Local Beach: Kailua
Brand Affiliation: None
Has thanked: 10 times
Been thanked: 2 times

Re: DIY Home Made wooden Hydrofoil fins

Postby Hawaiis » Wed Nov 13, 2013 11:29 pm

The Tuttle box used by raceboards should work, I just can not find them in the States for sale.
Anyone knows where to buy them?

Mahalo
Attachments
image.jpg
image.jpg (83.54 KiB) Viewed 2937 times

ozchrisb
Frequent Poster
Posts: 289
Joined: Sat Dec 29, 2012 2:59 am
Brand Affiliation: None
Has thanked: 0
Been thanked: 0

Re: DIY Home Made wooden Hydrofoil fins

Postby ozchrisb » Wed Nov 13, 2013 11:46 pm

Hawaiis wrote:The Tuttle box used by raceboards should work, I just can not find them in the States for sale.
Anyone knows where to buy them?

Mahalo
EDIT: found the cheaper one further down the page
Yes I have one at home I bought from:
http://www.fiberglasssupply.com/Product ... #Sailboard
Get the plastic one
R54-4561
Chinook "Tuttle" Plastic Race Box, Chinook (#305)
$16.26

They have all kinds of other box and glassing supplies too.

User avatar
Hawaiis
Very Frequent Poster
Posts: 1375
Joined: Wed Aug 24, 2011 11:39 am
Local Beach: Kailua
Brand Affiliation: None
Has thanked: 10 times
Been thanked: 2 times

Re: DIY Home Made wooden Hydrofoil fins

Postby Hawaiis » Thu Nov 14, 2013 1:01 am

ozchrisb wrote:
Hawaiis wrote:The Tuttle box used by raceboards should work, I just can not find them in the States for sale.
Anyone knows where to buy them?

Mahalo
EDIT: found the cheaper one further down the page
Yes I have one at home I bought from:
http://www.fiberglasssupply.com/Product ... #Sailboard
Get the plastic one
R54-4561
Chinook "Tuttle" Plastic Race Box, Chinook (#305)
$16.26

They have all kinds of other box and glassing supplies too.
do you have the dimensions ? There seem to be none on the internet even on Chinook's own website.

Mahalo

don pitcher
Frequent Poster
Posts: 210
Joined: Sat Aug 27, 2005 7:32 am
Has thanked: 0
Been thanked: 0

Re: DIY Home Made wooden Hydrofoil fins

Postby don pitcher » Thu Nov 14, 2013 3:02 am

Hawaiis wrote:the weight of the whole bottom unit is 2.55 kg
Compared to

MHL 3.7 kg
Carafino 4.35 kg
Rush Randle 5.5kg
MyWood 2.55 kg

Wow! A Carafino is that close in weight to a Rush Randle. While the MHL has much flex.

There really is a place for a low cost hydrofoil made of aluminum. Just have to find a source for a riser that is made of a hollow extrusion in a NACA shape.

User avatar
Hawaiis
Very Frequent Poster
Posts: 1375
Joined: Wed Aug 24, 2011 11:39 am
Local Beach: Kailua
Brand Affiliation: None
Has thanked: 10 times
Been thanked: 2 times

Re: DIY Home Made wooden Hydrofoil fins

Postby Hawaiis » Thu Nov 14, 2013 3:30 am

Sorry, my Private Message box does not allow me to reply, it only let me post it to the outbox and stayed there.

Stan:

You should check out my older posts, most of the information are listed, my research is still ongoing, when i finally finish the project, I will post the details on how to make one.
Sent: Wed Nov 13, 2013 5:24 pm
View message Reply with quote

oldkiter
Message subject: Your foil boardFolder: Inbox
I showed your video on your homemade foil board to a friend and he wants to make one for himself - he was very impressed. Can you provide some more specific info other than that on your description with the video.

Thanks,

Stan

zfennell
Very Frequent Poster
Posts: 975
Joined: Wed Nov 20, 2002 1:00 am
Brand Affiliation: None
Location: rhode island
Has thanked: 0
Been thanked: 0

Re: DIY Home Made wooden Hydrofoil fins

Postby zfennell » Fri Nov 15, 2013 9:15 pm

don pitcher wrote:
Hawaiis wrote:the weight of the whole bottom unit is 2.55 kg
Compared to

MHL 3.7 kg
Carafino 4.35 kg
Rush Randle 5.5kg
MyWood 2.55 kg

Wow! A Carafino is that close in weight to a Rush Randle. While the MHL has much flex.

There really is a place for a low cost hydrofoil made of aluminum. Just have to find a source for a riser that is made of a hollow extrusion in a NACA shape.
Don,
if you were to find a hollow aluminum strut with overall dimensions
-chord lenth: 4 in
-profile thickness: .59in (15mm)
-wall thickness: .1 in
-span length: 39 in

the foil would closely match the stuffness numbers provided by Europ2 in his thread.
weight of strut would be approx 2.7 lbs

personally, i doubt the foil needs to have any specific profile.
naca, ellipse, circular arcs... as long as it's streamlined.
i wonder how much laterall lift (from the strut) the rider could actually tolerate while standing on top of the entire mess. ( i'm guessing that its not much)
i'd certainly like to hear from folks that know better.
-bill

don pitcher
Frequent Poster
Posts: 210
Joined: Sat Aug 27, 2005 7:32 am
Has thanked: 0
Been thanked: 0

Re: DIY Home Made wooden Hydrofoil fins

Postby don pitcher » Fri Nov 15, 2013 10:35 pm

zfennell wrote:personally, i doubt the foil needs to have any specific profile.
naca, ellipse, circular arcs... as long as it's streamlined.
That is what I was thinking. I have been tempted by the aluminum extrusion below. But, I wish there was more wall thickness.

Image

http://www.bcawnings.com/?o=modules&n=a ... idinfo=899




I want to get rid of my frame and add a streamlined riser. I might have to give the extrusion above a try.

Image

zfennell
Very Frequent Poster
Posts: 975
Joined: Wed Nov 20, 2002 1:00 am
Brand Affiliation: None
Location: rhode island
Has thanked: 0
Been thanked: 0

Re: DIY Home Made wooden Hydrofoil fins

Postby zfennell » Fri Nov 15, 2013 11:30 pm

don,
just for comparisons:
if you use a measurement system like Europ2...

the 3" x 9/16" x 1/16" strut from bcawning will flex 2" :::::correction: 3/4 in

if you increase the wall thickness to .1", flex will reduce to 1-1/4" :::corrrection: 1/2in

a similar shape that's 4" x 9/16" x .1" will flex only 1/2"
this is similar to the numbers from Europ2 measurements.

certainly not the answer, just relative differences.
-bill
Last edited by zfennell on Sat Nov 23, 2013 3:16 pm, edited 1 time in total.


Return to “Hydrofoil”

Who is online

Users browsing this forum: alekbelia, Da Yoda, fleetrico, nixmatters and 148 guests