Contact   Imprint   Advertising   Guidelines

Drilling hardware

A forum dedicated to Hydrofoil riders
dylan*
Very Frequent Poster
Posts: 1047
Joined: Sat Mar 26, 2016 4:33 pm
Gear:
Has thanked: 1 time
Been thanked: 17 times

Drilling hardware

Postby dylan* » Sun Jan 21, 2018 9:57 pm

So I have a Hover Glide and I'm an idiot and let me bolts freeze up on my mast. Luckily I can still remove the plate from the board but the plate and fuselage are both cemented to the mast.

I understand I can drill them out, and there's a convenient youtube video specifically for this posted by Houston Kiteboarding.

Anything I should be aware of if I do this? I assume the bolts will be destroyed and I'll need to buy a new set. But is it as foolproof as it looks? Any chance of ruining the mast or anything in the process?

thewindego
Frequent Poster
Posts: 256
Joined: Wed Jan 18, 2017 3:13 am
Local Beach: Wolfe Island
Gear: core and windego boards
Brand Affiliation: None
Has thanked: 24 times
Been thanked: 37 times
Contact:

Re: Drilling hardware

Postby thewindego » Sun Jan 21, 2018 10:19 pm

You could try heating the plate to expand it with a torch but it will probable look a bit sad after. Opposite way would be dry ice or liquid nitrogen to shrink the mast if you have access to such.

User avatar
edt
Very Frequent Poster
Posts: 7309
Joined: Fri Jul 16, 2010 6:27 am
Kiting since: 2010
Local Beach: Michigan
Gear: ride hard, no regrets
Has thanked: 529 times
Been thanked: 658 times

Re: Drilling hardware

Postby edt » Sun Jan 21, 2018 11:11 pm

Be careful about using heat! You can ruin the temper on a high strength metal and make it very weak. As low as 350F (175C) can ruin the temper of aluminum and turn it into a noodle. Let us know how it goes.

OzBungy
Very Frequent Poster
Posts: 2750
Joined: Fri Oct 21, 2005 11:35 am
Has thanked: 6 times
Been thanked: 219 times

Re: Drilling hardware

Postby OzBungy » Mon Jan 22, 2018 12:59 am

Try soaking it in boiling water. That worked for me.

NorCalNomad
Very Frequent Poster
Posts: 838
Joined: Thu Feb 13, 2014 4:40 am
Local Beach: San Francisco
Gear: Why should it matter?
Has thanked: 0
Been thanked: 3 times

Re: Drilling hardware

Postby NorCalNomad » Mon Jan 22, 2018 2:07 am

This is an out there suggestion...but I wonder if strapping it to one of those paint shakers (like the ones at hardware stores) would induce enough vibrations to help loosen it. Other thought is find an ultrasonic parts/ jewelry cleaner to help break it free.

Also might be worth trying to soak it in high % rubbing alcohol since the surface tension of it is super low and might be enough to help free it.

User avatar
rynhardt
Very Frequent Poster
Posts: 977
Joined: Wed Sep 11, 2013 3:51 pm
Local Beach: Langebaan
Favorite Beaches: Langebaan
Style: Freeride
Gear: Cloud C2 17
Hoff Twinwave
Brand Affiliation: None
Location: Johannesburg, South Africa
Has thanked: 24 times
Been thanked: 29 times

Re: Drilling hardware

Postby rynhardt » Mon Jan 22, 2018 1:18 pm

Get yourself a screw extractor kit (easyout kit).
Also useful if one day you want to restore an old motorbike 8)

Dwight
Very Frequent Poster
Posts: 3377
Joined: Thu Aug 08, 2002 1:00 am
Local Beach: Florida
Gear: Any
Brand Affiliation: None
Has thanked: 1 time
Been thanked: 22 times

Re: Drilling hardware

Postby Dwight » Wed Jan 24, 2018 2:28 pm

Leave seized. Buy another base plate. I keep all my different mast sizes stored with base plates mounted permanently.

This makes for quick assembly of complete foil at beach.

FYI stainless steel is a difficult material to drill compared to regular steel. This will likely turn into a nightmare if you try. The drill bit may even wander into the softer aluminum, adding to your mess. When you finish, it’s likely some aluminum will be damaged and retapping will result in a sloppy screw fit. So then you have to the cut mast down to get fresh material for tapping.

Don’t do it unless you’re a pro at this type stuff.

User avatar
Kamikuza
Very Frequent Poster
Posts: 7057
Joined: Fri Jan 09, 2009 4:49 am
Local Beach: Sabae Beach
Favorite Beaches: Ol' Stinky
Gear: This, that, the other
Has thanked: 220 times
Been thanked: 193 times

Re: Drilling hardware

Postby Kamikuza » Wed Jan 24, 2018 2:57 pm

Dwight wrote:
Wed Jan 24, 2018 2:28 pm
Leave seized. Buy another base plate. I keep all my different mast sizes stored with base plates mounted permanently.

This makes for quick assembly of complete foil at beach.

FYI stainless steel is a difficult material to drill compared to regular steel. This will likely turn into a nightmare if you try. The drill bit may even wander into the softer aluminum, adding to your mess. When you finish, it’s likely some aluminum will be damaged and retapping will result in a sloppy screw fit. So then you have to the cut mast down to get fresh material for tapping.

Don’t do it unless you’re a pro at this type stuff.
This.

IIRC spare parts for the SS foil are very reasonably priced...

Europ2
Frequent Poster
Posts: 473
Joined: Wed Mar 01, 2006 7:51 pm
Brand Affiliation: None
Has thanked: 14 times
Been thanked: 7 times

Re: Drilling hardware

Postby Europ2 » Wed Jan 24, 2018 3:28 pm

Before drilling...... Coke has the ability to dissolve rust and many types of oxydation....
As a first test, put the plate/mast section down in 4 cm of coke cola in a bucket .... for 2 cays testing every 12 hrs ..

Then, do the same thing to the mast/fuse section. A plastic bin bag can be used as a tank for liquids. The mast/fuse section must be submerged.

Pls, post your results :wink:

User avatar
tegirinenashi
Very Frequent Poster
Posts: 815
Joined: Wed Aug 27, 2014 3:29 am
Local Beach: 3rd Ave
Gear: Bates 4000, Dominator MX-10
Brand Affiliation: None
Has thanked: 33 times
Been thanked: 36 times

Re: Drilling hardware

Postby tegirinenashi » Wed Jan 24, 2018 7:22 pm

Boiling water worked for me too. However, in my case it was fuse-mast connection. In your case the mast is wrapped in a collar, therefore, conducting heat to the mast is more challenging. The goal is to warm up the mast, while bolts still keep room temperature. As alum is good thermal conductor it may still work in your case, but I would follow the advise to leave it as it is. Corrosion on a plate/mast connection is not a problem at all, because the force is pushing one against the other, not pulling -- this is why bolts connecting them are relatively short.


Return to “Hydrofoil”

Who is online

Users browsing this forum: rynhardt and 60 guests